Author Topic: Chain Break guard  (Read 263 times)

0 Members and 0 Guests are viewing this topic.

Offline Rod in MN

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
  • Location: 10 North of St Cloud Minn.
Chain Break guard
« on: April 21, 2016, 10:40:30 am »
HI Guy's,  I have a Husqvarna Model E-Series  142  2005 I was just replacing the chain cover got a used one with no spring or band. Was just going to swap parts got the band, spring and the latch now to get the handle on so the brake will snap over I can not see how the arm and spring in handle fits in and will and move I did take some photos of it put could nut get a good one of the spring in handle???

Thank You
Rod in MN

Share on Facebook Share on Twitter


Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: Chain Break guard
« Reply #1 on: April 21, 2016, 02:00:24 pm »
REDNECK Saw Repair

Offline leec

  • 6 cube
  • ****
  • Posts: 264
  • Karma: 14
  • Location: Huntsville, Ontario
Re: Chain Break guard
« Reply #2 on: April 24, 2016, 02:18:47 pm »
Won't one off a cheapo Poulan (pre-stratos) also fit.  Just have to get used to a different colour.

Offline Rod in MN

  • 3 cube
  • *
  • Posts: 7
  • Karma: 0
  • Location: 10 North of St Cloud Minn.
Re: Chain Break guard
« Reply #3 on: April 24, 2016, 10:28:15 pm »
HI,  Thanks Guy's I got it working

Thank You
Rod in MN

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Chain Break guard
« Reply #4 on: May 15, 2016, 05:03:42 am »
Won't one off a cheapo Poulan (pre-stratos) also fit.  Just have to get used to a different colour.

The handle will swap over onto the 142 clutch cover.  The complete Poulan clutch cover won't fit on the Husky saw however.  While many parts (including the engines in many cases) will swap back and forth, the clutch covers themselves (and the starter covers, fuel tanks, and top covers) will not.  The two saw series are laid out very different, despite sharing so many internal parts.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
436 Views
Last post December 11, 2018, 04:09:16 pm
by fisaw
16 Replies
657 Views
Last post April 30, 2013, 02:58:57 pm
by HMLT360Pro
12 Replies
563 Views
Last post October 05, 2013, 09:25:13 am
by leec
26 Replies
821 Views
Last post February 03, 2014, 08:30:34 am
by SawTroll
15 Replies
371 Views
Last post December 12, 2013, 02:14:46 pm
by Gregsl
2 Replies
185 Views
Last post December 19, 2013, 11:47:37 pm
by RoyM
1 Replies
89 Views
Last post December 24, 2013, 11:36:57 pm
by Cut4fun .
3 Replies
283 Views
Last post January 09, 2014, 05:45:29 am
by KilliansRedLeo
12" bar guard/cover

Started by pigpen60 « 1 2 » Echo

16 Replies
555 Views
Last post August 19, 2014, 09:08:05 pm
by pigpen60
7 Replies
199 Views
Last post December 07, 2017, 08:13:22 am
by Cut4fun .