Author Topic: Figuring out Husky part numbers !!!  (Read 237 times)

0 Members and 0 Guests are viewing this topic.

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Figuring out Husky part numbers !!!
« on: February 18, 2015, 08:15:05 pm »
Does anyone have a chart that shows what Husky part numbers are for which model saw? I have a chart for Stihl, they are easy to figure out. I just bought a truck load of Husky parts and need to sort them all out.

Share on Facebook Share on Twitter


Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2055
  • Karma: 157
  • Location: MD
Re: Figuring out Husky part numbers !!!
« Reply #1 on: February 18, 2015, 08:25:57 pm »
Have seen some husky dealers online that have partsmart with a where used function.
http://www.bobsoutdoorpower.com/pages/OemParts?aribrand=HUS

In the box on the right at the bottom enter the part number hit enter. Will take you to another page that will tell you what it is and how much it cost. On the right side there will be a button that says model or something don't remember click there and it will pull up all the models in fits. Kind of a slow way to do it but better than nothing I guess. Hope it helps
FEAR NO TREE. FEAR GOD.

Offline fordrocks

  • 4 cube
  • **
  • Posts: 46
  • Karma: 2
Re: Figuring out Husky part numbers !!!
« Reply #2 on: February 18, 2015, 08:32:44 pm »
Thanks, i'll check it out.

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29
Re: Figuring out Husky part numbers !!!
« Reply #3 on: February 19, 2015, 10:14:29 am »
In addition to that, Jacks Small Engines has a good website for looking up part numbers as well, with diagrams.  Check them out.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22033
  • Karma: 544
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Figuring out Husky part numbers !!!
« Reply #4 on: February 19, 2015, 01:54:24 pm »
There used to be a parts site you could put the husky part number in and it would show all models of saws that took that part.

This one   http://www.husqvarna-parts-sales.com/Chain-Saw-Parts
REDNECK Saw Repair Getter Done

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: Figuring out Husky part numbers !!!
« Reply #5 on: February 20, 2015, 02:33:56 pm »
Most of the lookups will show list of saws the part fits. SEPW, Jacks, upstateoutdoorpowerequipment to name a few.  I use this one most of the time.  Doesn't give model on all of them tho.   Don't buy parts there just use the lookup.   http://www.smallenginepartswarehouse.com/p/husqvarna-parts?aribrand=HUS#
Shep

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: Figuring out Husky part numbers !!!
« Reply #6 on: February 21, 2015, 01:02:04 pm »
Most of the lookups will show list of saws the part fits. SEPW, Jacks, upstateoutdoorpowerequipment to name a few.  I use this one most of the time.  Doesn't give model on all of them tho.   Don't buy parts there just use the lookup.   http://www.smallenginepartswarehouse.com/p/husqvarna-parts?aribrand=HUS#
Shep
Looks very similar to the one jmester posted - likely the same software?

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Figuring out Husky part numbers !!!
« Reply #7 on: February 21, 2015, 02:09:08 pm »
www.ereplacementparts.com works well for this.  Put the part number in the search box.  Usually works best if you take the hyphens and spaces out of the number). 

Sometimes it's a bit broad in the "what it fits" department however.  That usually happens with saws in a series where there's multiple models with different bore diameters.  It'll at least get you close enough to know what series it's from.  You can then pull up an IPL from the www.husqvarna.com website (click 'manuals' within the 'support' section) and figure out what exact model it fits.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: Figuring out Husky part numbers !!!
« Reply #8 on: February 21, 2015, 09:42:23 pm »
Most of the lookups will show list of saws the part fits. SEPW, Jacks, upstateoutdoorpowerequipment to name a few.  I use this one most of the time.  Doesn't give model on all of them tho.   Don't buy parts there just use the lookup.   http://www.smallenginepartswarehouse.com/p/husqvarna-parts?aribrand=HUS#
Shep
Looks very similar to the one jmester posted - likely the same software?
From my experience they do use the same software.  I have 6-8 lookups all work & look the same.
Shep

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22033
  • Karma: 544
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Figuring out Husky part numbers !!!
« Reply #9 on: December 07, 2017, 11:36:32 am »
Bumping up for those that lost links http://www.husqvarna-parts-sales.com/Chain-Saw-Parts
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
8 Replies
1183 Views
Last post April 25, 2011, 08:32:59 pm
by Cut4fun
1 Replies
4577 Views
Last post May 09, 2011, 09:04:07 pm
by mcbob
5 Replies
676 Views
Last post January 18, 2013, 03:51:05 pm
by 660magnum
5 Replies
253 Views
Last post January 22, 2014, 02:46:36 pm
by danders
11 Replies
452 Views
Last post December 30, 2018, 08:12:28 pm
by Cut4fun .
8 Replies
221 Views
Last post May 22, 2014, 08:06:07 am
by KilliansRedLeo
4 Replies
194 Views
Last post August 02, 2014, 06:07:44 pm
by pigpen60
8 Replies
371 Views
Last post October 14, 2014, 07:17:32 am
by Trang77
2 Replies
649 Views
Last post March 20, 2016, 01:15:19 pm
by 660magnum
3 Replies
144 Views
Last post February 16, 2020, 09:53:17 am
by Cut4fun .