« previous next »
Pages: [1]   Go Down

Author Topic: Husky 266 Oil Tank Vent  (Read 718 times)

0 Members and 0 Guests are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Husky 266 Oil Tank Vent
« on: September 01, 2014, 08:15:25 am »
Oil tank vent for 61-266, etc. 501-6244-01 is NLA according to Jacks.  Ordered one hoping they might have didn't really think they would.  Any ideas on other options.  Need that to finish 266 I just did a top end on.
Shep
Logged

Share on Facebook Share on Twitter

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husky 266 Oil Tank Vent
« Reply #1 on: September 02, 2014, 12:08:46 pm »
Shep, post a picture of the one you need, I'll look through all my 266 stuff.
Tim
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: Husky 266 Oil Tank Vent
« Reply #2 on: September 02, 2014, 12:44:02 pm »
Can't do pic.  It's the small one held in by a star washer.  Evidentally this one was used in a couple of YM.  After this one they used one that was press fit PN: 501-6244-01 (1984 up.
Shep
Logged

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husky 266 Oil Tank Vent
« Reply #3 on: September 02, 2014, 01:39:22 pm »
Shep, is this the one you need? It is actually on an old 272. If it is the one, how the hell do you get it out? Never mind, that is not it. I'll look some more.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husky 266 Oil Tank Vent
« Reply #4 on: September 02, 2014, 01:57:21 pm »
OK Shep, I think I have one, it is on a 266SE case I have. Question now is how do I get it out? Looks to be installed from the inside of the case. located on top of the case under the corner of the muffler.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husky 266 Oil Tank Vent
« Reply #5 on: September 02, 2014, 03:31:26 pm »
Shep the one I have uses the press-in plug. However the partstree.com web page for the saw shows


503270301 Husqvarna 503270301 SNAP WASHER
 
501624401 Husqvarna 501624401 VALVE PLUG

As both being available.
 
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 150
  • Location: Hayesville, NC
Re: Husky 266 Oil Tank Vent
« Reply #6 on: September 02, 2014, 10:03:27 pm »
Thanks Tim.  Got to thinking it is held in by the snap washer I'm going to try and get the snap washer out of another case and see what happens. LOL
Shep
Logged

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husky 266 Oil Tank Vent
« Reply #7 on: September 03, 2014, 09:35:37 am »
From the IPL it looks like the vent goes in the case from the top and the snap ring goes in last. So a very small snap ring tool or a tiny screwdriver should do it.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
11 Replies
1475 Views 		Last post November 30, 2011, 06:59:41 pm
by bama
7 Replies
3686 Views 		Last post April 23, 2013, 04:21:14 pm
by Go JayBee
16 Replies
2097 Views 		Last post April 11, 2014, 07:03:51 am
by Tractorsaw1
14 Replies
623 Views 		Last post December 01, 2015, 05:46:32 am
by Gregg MacPherson
4 Replies
285 Views 		Last post March 10, 2014, 11:29:40 pm
by farmboy
4 Replies
564 Views 		Last post September 15, 2014, 03:41:07 am
by Eccentric
20 Replies
1241 Views 		Last post September 09, 2015, 02:29:33 pm
by 94BULLITT
1 Replies
730 Views 		Last post September 17, 2017, 10:19:30 pm
by Cut4fun .
0 Replies
126 Views 		Last post November 25, 2020, 08:52:46 am
by Cut4fun .
0 Replies
119 Views 		Last post March 02, 2023, 07:16:55 am
by Cut4fun .