Author Topic: Husky 435 starts but won't rev  (Read 147 times)

0 Members and 0 Guests are viewing this topic.

Offline bsaumph

  • pruner
  • *
  • Posts: 3
  • Karma: 1
Husky 435 starts but won't rev
« on: September 01, 2018, 03:54:08 pm »
Saw starts hard but will sorta idle. Bogs down and dies if given any throttle.
This condition came on slowly. When the problem started I could start it and after a few minutes it would rev normally. Condition steadily got worse until it wont rev at all now.

have replaced the carb : no change
inspected fuel lines: all seem in good condition
Blew through fuel filter : doesn't seem plugged
Now what??
Thanks

Share on Facebook Share on Twitter


Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1170
  • Karma: 149
  • Location: Hayesville, NC
Re: Husky 435 starts but won't rev
« Reply #1 on: September 01, 2018, 10:04:25 pm »
Fought one for weeks.  Replaced carb 3 times w/new OEM.  Replaced coil good to go.  Coil goes bad when it advances timing. New OEM coil $22.00.  Got one on Ebay $15.00 del.
Shep
Agree Agree x 1 Informative Informative x 1 View List

Offline bsaumph

  • pruner
  • *
  • Posts: 3
  • Karma: 1
Re: Husky 435 starts but won't rev
« Reply #2 on: September 03, 2018, 02:17:45 pm »
Thanks for the info. guess i'll try a coil.
Like Like x 1 View List

Offline bsaumph

  • pruner
  • *
  • Posts: 3
  • Karma: 1
Re: Husky 435 starts but won't rev
« Reply #3 on: September 12, 2018, 03:41:52 pm »
Fought one for weeks.  Replaced carb 3 times w/new OEM.  Replaced coil good to go.  Coil goes bad when it advances timing. New OEM coil $22.00.  Got one on Ebay $15.00 del.
Shep
You my friend are a life saver. New coil and she runs like new. The coil would have been one of the last things I would have suspected since it would run. Thank you again!!
Like Like x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
115 Replies
5578 Views
Last post July 13, 2020, 11:35:20 pm
by 3000 FPS
13 Replies
935 Views
Last post March 09, 2012, 01:51:34 pm
by eli-dream
17 Replies
710 Views
Last post February 12, 2013, 07:48:58 am
by bassman
6 Replies
304 Views
Last post June 16, 2013, 08:56:25 am
by Al Smith
16 Replies
437 Views
Last post December 27, 2013, 05:37:28 am
by 660magnum
7 Replies
453 Views
Last post October 29, 2014, 03:58:59 pm
by Fish
15 Replies
443 Views
Last post January 23, 2015, 02:03:24 pm
by Bluegill
21 Replies
631 Views
Last post September 14, 2015, 06:21:22 pm
by jeff.lary
4 Replies
167 Views
Last post March 30, 2018, 10:35:37 am
by joel4bs
2 Replies
226 Views
Last post July 04, 2018, 08:14:36 am
by Cut4fun .