« previous next »
Pages: 1 [2]   Go Down

Author Topic: Husq 254 questions  (Read 1002 times)

0 Members and 63 Guests are viewing this topic.

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29

    • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary 100 Posts Level 3 One year Anniversary 50 Posts
Re: Husq 254 questions
« Reply #10 on: November 19, 2016, 08:26:23 am »
Quote from: Eccentric on November 19, 2016, 04:59:22 am
Crank seals are leaking when it gets hot, causing it to lean out and bog.  Hopefully the piston and cylinder aren't damaged yet.  Leaning out under load like that can and will cause damage...
That's an "advanced issue".  Lol
Logged

Offline laferret

  • pruner
  • *
  • Posts: 4
  • Karma: 0

    • Total Badges: 3
    Badges: (View All)
    Level 1 Search Windows User
Re: Husq 254 questions
« Reply #11 on: November 19, 2016, 08:34:24 am »
The pot and piston are being replaced anyway so I'm not concerned about those too much. The mechanic has plenty of experience changing crank bearings on stihl abrasive cutters so it's just a case of diagnosis and finding the parts supplier if they aren't too expensive.
Thanks for all your input.

Sent from my E6653 using Tapatalk

Logged

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29

    • Total Badges: 14
    Badges: (View All)
    Third year Anniversary Second year Anniversary 100 Posts Level 3 One year Anniversary 50 Posts
Re: Husq 254 questions
« Reply #12 on: November 19, 2016, 08:54:42 am »
Quote from: laferret on November 19, 2016, 08:34:24 am
The pot and piston are being replaced anyway so I'm not concerned about those too much. The mechanic has plenty of experience changing crank bearings on stihl abrasive cutters so it's just a case of diagnosis and finding the parts supplier if they aren't too expensive.
Thanks for all your input.

Sent from my E6653 using Tapatalk


Your kindly welcome Laferret, and hope you enjoy the site.  Hopefully it won't cost you an arm and a leg for repairs.  Nevertheless, keep us posted on the outcome, as we all learn from these things, and have a great weekend sir :)
Logged

Offline laferret

  • pruner
  • *
  • Posts: 4
  • Karma: 0

    • Total Badges: 3
    Badges: (View All)
    Level 1 Search Windows User
Re: Husq 254 questions
« Reply #13 on: November 21, 2016, 09:02:38 am »
So the service kit has arrived and I've been asked to source some starter pawls. I've found a supplier but the prices are cosmic! £5.72 each and £2.50 for each spring. Anyway while I'm there I thought I'd get your view on the drive sprocket to see if it needs replacing?
He's also had the oil pump apart and it was full of old saw dust which seems like a design flaw if the only way to clean it is to remove the clutch etc.


Sent from my E6653 using Tapatalk

Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming

    • Total Badges: 37
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: Husq 254 questions
« Reply #14 on: November 24, 2016, 03:59:02 pm »
Quote from: wild262 on November 19, 2016, 08:26:23 am
Quote from: Eccentric on November 19, 2016, 04:59:22 am
Crank seals are leaking when it gets hot, causing it to lean out and bog.  Hopefully the piston and cylinder aren't damaged yet.  Leaning out under load like that can and will cause damage...
That's an "advanced issue".  Lol

Eh......maybe so.

But..........it's an issue that is often ignored.  I've seen folks put a new P/C on a saw that "was straight gassed" (what many folks MUST be the cause of a roached p/c), only to have the new p/c burn up not long afterwards as they didn't cure the real cause of the original failure (air leak, too lean carburetor adjustment, dull chain, or some combination of those).
Logged
Like Like x 1 View List
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1396 Views 		Last post August 19, 2012, 11:48:10 am
by man of stihl
3 Replies
583 Views 		Last post December 19, 2012, 12:52:30 am
by 660magnum
2 Replies
698 Views 		Last post November 24, 2013, 08:37:21 pm
by alsled
10 Replies
750 Views 		Last post January 29, 2014, 05:51:39 am
by neil
1 Replies
488 Views 		Last post April 06, 2014, 01:26:38 pm
by KilliansRedLeo
15 Replies
713 Views 		Last post June 05, 2014, 01:17:33 pm
by Eliott
13 Replies
732 Views 		Last post December 22, 2014, 01:50:28 am
by 660magnum
0 Replies
432 Views 		Last post January 27, 2017, 04:19:54 pm
by waltergorman
1 Replies
314 Views 		Last post May 10, 2021, 05:52:40 am
by Spike60
1 Replies
257 Views 		Last post March 19, 2023, 07:01:57 am
by Cut4fun .