Author Topic: Husqvarna 353  (Read 4912 times)

0 Members and 1 Guest are viewing this topic.

Offline John Mc

  • 5 cube
  • ***
  • Posts: 125
  • Karma: 12
  • Vermont
  • Location: Vermont
Re: Husqvarna 353
« Reply #50 on: April 23, 2015, 05:20:41 pm »
2007 husky 353 just dropped off. Says leaks the bar oil out in puddles.   No matter how many times he sets saw around garage it puddles everywhere. 

Wasnt there a oiler line update to these?

My Jonsered 2152 has leaked oil since it was new. (The dealer at the time just said "they all do that".) If there was an update to the 353, did it apply to the 2152 as well? I'd love to get this fixed. It's a bummer to end up with oil everywhere it sits - besides, I often have to use the canola oil-based bar oil, and that stuff is not cheap.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 353
« Reply #51 on: April 23, 2015, 05:54:25 pm »
2007 husky 353 just dropped off. Says leaks the bar oil out in puddles.   No matter how many times he sets saw around garage it puddles everywhere. 

Wasnt there a oiler line update to these?

My Jonsered 2152 has leaked oil since it was new. (The dealer at the time just said "they all do that".) If there was an update to the 353, did it apply to the 2152 as well? I'd love to get this fixed. It's a bummer to end up with oil everywhere it sits - besides, I often have to use the canola oil-based bar oil, and that stuff is not cheap.

In 2012 I found where I posted this. But cant any info on it or starting what years. The 346's  was updated oiler lines later in run.

Hopefully I didnt just imagine that. Maybe someone knows. I would say if we bought new lines they will be updated.  Wonder if 1 piece over older 2 piece design.
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 353
« Reply #52 on: April 23, 2015, 05:57:35 pm »
Anything on this @Spike60
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 353
« Reply #53 on: April 23, 2015, 06:11:10 pm »
This guy has some good info. I am going to try threebond 1194 instead of grease though.

Down to where we can start seeing the origin of the leak. Green arrow points to where it seems to be oozing. The area where the yellow arrow points to is completely dry, so oil is not leaking down from where the oil tube meets the bar.





Pulled the tube that runs from the oil pump up to the bar. The Green arrow points to a nipple on the pump that the oil tube seats to. This is a possible leak source.





Removed the oil pump. Here the green arrow points to a rubber saddle that the oil pump seats into with the same type of nipple on the outer side. Same possible leak source. The rubber saddle itself seats into the oil tank which could be another possible leak source.






 put grease on both sides of the oil pump nipples.











REDNECK Saw Repair Getter Done

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2046
  • Karma: 156
  • Location: MD
Re: Husqvarna 353
« Reply #54 on: April 23, 2015, 08:22:20 pm »
Very nice pics and explanation.
FEAR NO TREE. FEAR GOD.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Husqvarna 353
« Reply #55 on: April 23, 2015, 11:02:40 pm »
What provides tension on that nipple normally? Bar plate?   Funky design....

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 353
« Reply #56 on: April 24, 2015, 12:53:02 am »
The oil pickup line seals against the backside of the oil pump.  Pressure there comes from the oil pump mounting screws.  The discharge line is held against the pump by the inner bar plate/oil pump cover tin.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Husqvarna 353
« Reply #57 on: April 24, 2015, 09:10:53 am »
Aaron Thanks.  Pressing the outlet rubber on an irregular (rounded) surface would tend to open up the rubber tube IMO.  Looks like a good fix above. Wonder if cynoacrylate type glues would bond the rubber to the aluminum if the metal was scuffed up?

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 353
« Reply #58 on: April 24, 2015, 07:33:54 pm »
Sure looks updated to me.   Appears 1 piece design and the bar mount oiler channel area seems different.  The rubber part going up is short and then just metal channel.    ???

Was still leaking right from that same area though shown in thise pics above.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21874
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 353
« Reply #59 on: April 24, 2015, 08:14:56 pm »
503 85 48-01  503854801 

Looks like it was the part that was used on the husqvarna 350 IPL http://www.husqvarna.com/ddoc/husi/husi1999_aaaa/husi1999_aaaa_i9900054_.pdf



REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
7 Replies
478 Views
Last post January 31, 2016, 12:49:24 pm
by 660magnum
0 Replies
125 Views
Last post March 30, 2016, 07:10:38 pm
by mikehonda
4 Replies
260 Views
Last post April 12, 2016, 06:30:34 pm
by dannyupsolate
4 Replies
335 Views
Last post November 07, 2016, 05:46:56 pm
by oldpro
2 Replies
272 Views
Last post May 15, 2016, 04:59:09 am
by Eccentric
20 Replies
951 Views
Last post March 21, 2018, 10:47:30 am
by Cut4fun .
4 Replies
328 Views
Last post November 23, 2016, 02:23:26 am
by georgehopson
1 Replies
164 Views
Last post October 26, 2016, 03:40:28 pm
by Eccentric
Husqvarna 61

Started by Cut4fun « 1 2 » Husqvarna

17 Replies
284 Views
Last post October 28, 2016, 02:39:12 pm
by Eccentric
0 Replies
370 Views
Last post January 16, 2017, 03:40:49 pm
by HolmenTree