« previous next »
Pages: 1 [2]   Go Down

Author Topic: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller  (Read 680 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2112
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller
« Reply #10 on: April 10, 2015, 06:35:47 pm »
Looks like they upped the price a bit....
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 3993
  • Karma: 155
  • OHIO REDNECK
Re: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller
« Reply #11 on: December 18, 2017, 08:33:29 am »
Guy need a crankshaft from for a 142 and he said a 141 will work. I took his word for it and mailed him a 141 crankshaft.
I found out I didnt have anything on hand to pull a 141 worm gear so I was looking and found this thread.

Anyone know for sure on the cranks 142 141 same?
Logged
REDNECK Saw Repair

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21625
  • Karma: 505
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller
« Reply #12 on: December 18, 2017, 08:56:22 am »
Quote from: Cut4fun on December 18, 2017, 08:33:29 am
Guy need a crankshaft from for a 142 and he said a 141 will work. I took his word for it and mailed him a 141 crankshaft.
I found out I didnt have anything on hand to pull a 141 worm gear so I was looking and found this thread.

Anyone know for sure on the cranks 142 141 same?

Already confirmed yes on CR group.
Logged
REDNECK Saw Repair Getter Done

Online ray benson

  • 5 cube
  • ***
  • Posts: 120
  • Karma: 59
  • Retired Industrial Electrician
  • Location: Indiana
Re: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller
« Reply #13 on: December 18, 2017, 09:54:40 am »
Looked at a 141 and 142 ipl. Both use the #530029744 crank and rod assembly. Looks like a Poulan part #, the 136 also uses the same part.
Barretts is your friend.
http://www.barrettsmallengine.com/husqvarna/chainsawpartslist.html
Logged
Like Like x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21625
  • Karma: 505
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 36/41/136/137/141 Oil Pump Worm Gear Puller
« Reply #14 on: December 18, 2017, 06:48:12 pm »
I was on the run so no time to look stuff up myself.

Thanks though for the help here too.
Logged
REDNECK Saw Repair Getter Done
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
6 Replies
1610 Views 		Last post March 09, 2012, 06:30:02 pm
by Cut4fun .
2 Replies
286 Views 		Last post July 19, 2012, 08:02:44 pm
by Cut4fun .
1 Replies
156 Views 		Last post October 10, 2013, 10:18:54 pm
by 660magnum
18 Replies
216 Views 		Last post January 11, 2015, 03:10:06 pm
by 604f_1
0 Replies
112 Views 		Last post November 03, 2016, 01:27:09 pm
by Cut4fun .
7 Replies
404 Views 		Last post February 25, 2017, 03:59:30 am
by dutchsawdoctor
3 Replies
164 Views 		Last post April 20, 2017, 02:46:52 pm
by Cut4fun .
0 Replies
196 Views 		Last post December 12, 2017, 03:59:50 pm
by Cut4fun .
1 Replies
105 Views 		Last post December 13, 2018, 04:19:47 pm
by Cut4fun .
3 Replies
124 Views 		Last post June 04, 2019, 08:36:12 am
by ray benson