Author Topic: Husqvarna 365 throttle hanging up?  (Read 523 times)

0 Members and 0 Guests are viewing this topic.

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: Husqvarna 365 throttle hanging up?
« Reply #40 on: December 14, 2013, 12:08:23 pm »
Well I found the problem as far as it dieing, it was full of crap, the screen was plugged.

 Still have a problem though, The idle screw has to be turned in almost all the way, then it needs 3 turns out on low speed screw to idle right, and I can turn the hi speed screw in all the way and it runs fine wot.  I sprayed some carb cleaner around the carb and the saw dies instantly.
 
Ends up its sucking air from the throttle shaft and carb bore, shat is fine, bore seems bad, there is about .015 play in the shaft and bore.  So now to hunt up a different carb.

Any one got a good one?

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husqvarna 365 throttle hanging up?
« Reply #41 on: December 14, 2013, 12:22:39 pm »
You can get an aftermarket one from HLS for $30. I may have a used one around here if you want to come get it. I may also have a new AM one here as well.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: Husqvarna 365 throttle hanging up?
« Reply #42 on: December 14, 2013, 12:27:26 pm »
Whats a AM one?

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husqvarna 365 throttle hanging up?
« Reply #43 on: December 14, 2013, 12:32:31 pm »
After market not a Walbro
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husqvarna 365 throttle hanging up?
« Reply #44 on: December 14, 2013, 12:38:04 pm »
DO NOT THROW THE OLD CARB OUT!!

The little white bell crank for the throttle cable is NOT a Walbro part and does not come with the carb. It is a Husqvarna part and you will need to transfer it to the new carb.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: Husqvarna 365 throttle hanging up?
« Reply #45 on: December 14, 2013, 12:50:15 pm »
I never throw anything out, goes in the spare parts bucket.  : )

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: Husqvarna 365 throttle hanging up?
« Reply #46 on: December 14, 2013, 12:53:11 pm »
Plus it has a new rebuild kit in it that I have to take out.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Husqvarna 365 throttle hanging up?
« Reply #47 on: December 22, 2013, 07:16:57 pm »
Alan, did the new carb cure your problems?
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline alsled

  • Piped Saw
  • *****
  • Posts: 307
  • Karma: 18
Re: Husqvarna 365 throttle hanging up?
« Reply #48 on: December 22, 2013, 11:15:48 pm »
Ice storm hit here, been busy putting wires back up, along with fixing blown up snowblowers.


 

Related Topics

  Subject / Started by Replies Last post
2 Replies
324 Views
Last post January 31, 2012, 07:12:57 pm
by Old Iron Logging
8 Replies
383 Views
Last post November 13, 2012, 09:44:27 pm
by Al Smith
9 Replies
1035 Views
Last post December 19, 2012, 10:28:20 am
by HolmenTree
6 Replies
170 Views
Last post April 03, 2014, 03:39:41 pm
by bigtuna
16 Replies
342 Views
Last post November 26, 2014, 07:19:05 am
by Sty57
6 Replies
64 Views
Last post July 15, 2014, 10:38:33 am
by aclarke
2 Replies
268 Views
Last post September 23, 2014, 08:50:25 pm
by weimedog
7 Replies
160 Views
Last post February 06, 2015, 12:30:00 pm
by Cut4fun .
15 Replies
293 Views
Last post November 23, 2015, 04:10:04 pm
by tassin85
6 Replies
1639 Views
Last post January 08, 2016, 07:31:28 am
by 67L36Driver