« previous next »
Pages: 1 ... 7 8 9 10 11 [12] 13   Go Down

Author Topic: Husqvarna 365 X-Torq  (Read 14767 times)

0 Members and 1 Guest are viewing this topic.

Offline John Mc

  • 6 cube
  • ****
  • Posts: 158
  • Karma: 14
  • Location: Addison Co, VT
Re: Husqvarna 365XP X-Torq
« Reply #110 on: April 11, 2012, 09:00:04 am »
3400 RPM didn't have his chain spinning at idle?
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: Husqvarna 365XP X-Torq
« Reply #111 on: April 11, 2012, 09:22:33 am »
Quote from: Spike60 on April 11, 2012, 07:21:25 am
The coils on these saws can cause an erratic idle problem. The ignition advance is supposed to kick in at about the same RPM as clutch engagement. In some cases it seems that the advance can come in a little sooner. Combine that with a static idle adjustment that's a little too high, and the idle surges up and down and drives you nuts. It has nothing to do with the mixture screws, and messing with them just adds to the confusion.

I was cutting with a buddy on Saturday and his new 365/372 was doing this exact thing. The idle was only at 3400 and the coil was wigging out with the advance coming and going. Turned it down to 2800-2900 and the idle smoothed right out.

Also, the old unlimted coil can be used in these new XT saws regardless of which coil/carb combo they came with.

First two cuts in video are with OE coil.  Last is unlimited.  They do act funny from time to time.
Logged

Offline foxtrapper

  • pruner
  • *
  • Posts: 1
  • Karma: 0
Re: Husqvarna 365XP X-Torq
« Reply #112 on: April 17, 2012, 06:28:42 pm »
I purchased a 365xt in November and have been very impressed with the saw. I also have a 372xp.  I would like to know if I could put the xtorque cylindar and  piston on the 372 or if the crank shaft also needs to be changed. I realize the plastic cover would have to be changed to accomadate the taller cylinder.
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: Husqvarna 365XP X-Torq
« Reply #113 on: April 17, 2012, 08:24:23 pm »
Quote from: foxtrapper on April 17, 2012, 06:28:42 pm
I purchased a 365xt in November and have been very impressed with the saw. I also have a 372xp.  I would like to know if I could put the xtorque cylindar and  piston on the 372 or if the crank shaft also needs to be changed. I realize the plastic cover would have to be changed to accomadate the taller cylinder.

P&C will bolt right up but you will need the XT intake and possibly the carb...depending on how you want it set up.
Logged

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80
Re: Husqvarna 365XP X-Torq
« Reply #114 on: May 29, 2012, 08:57:12 pm »
Ok I did a 365 xt today and I donot know why people donot like these saws , this thing is a down right animal in the wood , it has no pop up, no flywheel work, no carb work and pulls a very hard 12,600 rpms in the wood and I cut hard maple to test times with , it has way more torque than the older 372's have period , if I back off just a touch on pushing its on the limiter at 13,500 , I put videos up on youtube and this saw is going to be used by a timber faller every day 6 or so days a week , its not build to be a cookie cutter but I know alot of cookie cutters will not like this saw
Logged

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80
Re: Husqvarna 365XP X-Torq
« Reply #115 on: May 29, 2012, 11:54:32 pm »
here is the 365 xt , Man I'm pushing very hard on her and she likes it http://www.youtube.com/watch?v=-PrR6NtlFrc&list=UUU6spuQiscFB7QpsHWOjnsQ&index=2&feature=plcp
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23288
  • Karma: 655
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 365XP X-Torq
« Reply #116 on: May 30, 2012, 12:39:39 pm »
Looks and sounds great.

Todays best bargain in a 71cc saw IMO . Under $600 new here with b+c.
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: Husqvarna 365XP X-Torq
« Reply #117 on: May 30, 2012, 01:15:17 pm »
Quote from: Cut4fun2 on May 30, 2012, 12:39:39 pm
Looks and sounds great.

Todays best bargain in a 71cc saw IMO . Under $600 new here with b+c.

My thoughts exactly.  Like the low top too
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23288
  • Karma: 655
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 365XP X-Torq
« Reply #118 on: June 18, 2012, 02:22:07 pm »
Getem now. July 1st you are going to see a $110 price increase on the 365xt.  :o
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: Husqvarna 365XP X-Torq
« Reply #119 on: June 18, 2012, 02:29:28 pm »
Quote from: Cut4fun2 on June 18, 2012, 02:22:07 pm
Getem now. July 1st you are going to see a $110 price increase on the 365xt.  :o


Should have seen that coming
Logged
Pages: 1 ... 7 8 9 10 11 [12] 13   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
10 Replies
2816 Views 		Last post May 03, 2011, 09:49:54 pm
by blsnelling
2 Replies
805 Views 		Last post July 23, 2012, 07:49:15 am
by 660magnum
9 Replies
1430 Views 		Last post November 17, 2012, 09:05:18 pm
by Mw1995
5 Replies
520 Views 		Last post January 05, 2013, 11:35:08 pm
by 660magnum
0 Replies
166 Views 		Last post March 03, 2013, 08:14:40 pm
by Cut4fun
19 Replies
1164 Views 		Last post November 10, 2013, 08:11:53 pm
by KilliansRedLeo
7 Replies
401 Views 		Last post February 28, 2016, 07:32:00 pm
by 660magnum
2 Replies
238 Views 		Last post May 07, 2018, 02:36:08 pm
by Cut4fun .
4 Replies
359 Views 		Last post July 12, 2018, 09:03:40 am
by ray benson
12 Replies
301 Views 		Last post October 19, 2022, 08:30:49 pm
by EHP