Author Topic: Husqvarna 372xp  (Read 8186 times)

0 Members and 0 Guests are viewing this topic.

Offline blsnelling

  • 4 cube
  • **
  • Posts: 58
  • Karma: 7
Re: Husqvarna 372xp
« Reply #10 on: February 26, 2011, 01:53:52 pm »
Use some really nasty solvents and give it some good heating to burn out as much oil as possible before applying whatever sealant.

One possible to use in a fine crack like this is Locktite. Seap it in and seal with some tape for a while, Locktite hardens from lack of air.
What concerns me about this crack is that it's in the bar mount area and sees some stresses.  I'm not sure you'd want to split the cases, but the best fix would be from inside.  Drill small holes at both ends of the crack, bevel the crack a little, rough up real good around it, and then JBWeld it.  I did a similiar repair to a 015 and my BIL is still using it.

Offline jamming

  • 4 cube
  • **
  • Posts: 44
  • Karma: 1
  • Location: Diablo, wa
Re: Husqvarna 372xp
« Reply #11 on: February 26, 2011, 02:51:17 pm »
Be sure and post how you fixed this or didnt, would really be curious !
I drives me boat my wife drives me dingy

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4048
  • Karma: 159
  • OHIO REDNECK
Re: Husqvarna 372xp
« Reply #12 on: February 26, 2011, 03:14:36 pm »
Be sure and post how you fixed this or didnt, would really be curious !

It's going to be awhile ok, it is very low on priority list right now.
REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Husqvarna 372xp
« Reply #13 on: March 20, 2011, 02:38:55 pm »
my new toy ;) 20'' bar with stihl RSC chain
Ron

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4048
  • Karma: 159
  • OHIO REDNECK
Re: Husqvarna 372xp
« Reply #14 on: March 20, 2011, 03:29:08 pm »
Appears to be woods ported  cutting like that  :o
REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Husqvarna 372xp
« Reply #15 on: March 20, 2011, 05:40:40 pm »
i think it may have had a little work done to it. ;)
Ron

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4048
  • Karma: 159
  • OHIO REDNECK
Re: Husqvarna 372xp
« Reply #16 on: March 20, 2011, 06:21:01 pm »
i think it may have had a little work done to it. ;)

Your work or who's? 

It sounds like one of 2 porters who's 372's sound like that. The one used to port for the other till the other starting porting for himself. Both goooood builders.
REDNECK Saw Repair

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Husqvarna 372xp
« Reply #17 on: March 20, 2011, 06:34:47 pm »
Definitely not my work. Thats a Dan Henry build.
Ron

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4048
  • Karma: 159
  • OHIO REDNECK
Re: Husqvarna 372xp
« Reply #18 on: March 31, 2011, 05:51:14 pm »
Guys asking me for a 50mm 372. I have plenty but hard to conform to the rules that have been set.
Some of my saws have red in them, some have 362 365 tags, some have BB on 372 and 372xpg tags, some are already ported. But I do have plenty of 50mm stock tops and crankcases they could go on. Just replace the tags with a 372xp tag.  Husky tags are known to come off and get lost.  ;)

Few I have left.

REDNECK Saw Repair

Offline mdavlee

  • 5 cube
  • ***
  • Posts: 138
  • Karma: 4
Re: Husqvarna 372xp
« Reply #19 on: March 31, 2011, 06:25:44 pm »
I think the 365s will be ok. Just needs to be a 50mm topend.

 

Related Topics

  Subject / Started by Replies Last post
4 Replies
1157 Views
Last post February 21, 2012, 09:43:13 am
by mweba
32 Replies
992 Views
Last post March 26, 2013, 02:48:36 pm
by UNCLEBEEF
5 Replies
333 Views
Last post September 14, 2013, 11:32:12 am
by turbo885
7 Replies
651 Views
Last post October 23, 2013, 10:49:55 pm
by Walt
14 Replies
1154 Views
Last post December 22, 2013, 06:21:33 am
by brokenbudget
17 Replies
389 Views
Last post January 29, 2015, 10:28:10 am
by Spike60
15 Replies
399 Views
Last post September 07, 2015, 06:40:03 pm
by Cut4fun .
6 Replies
418 Views
Last post December 06, 2016, 08:09:47 am
by wild262
2 Replies
91 Views
Last post May 07, 2018, 02:36:08 pm
by Cut4fun .
8 Replies
373 Views
Last post January 05, 2019, 09:48:58 am
by trappermike