Author Topic: Husqvarna 385xp bearings & seals  (Read 279 times)

0 Members and 0 Guests are viewing this topic.

Offline weimedog

  • 6 cube
  • ****
  • Posts: 260
  • Karma: 57
Husqvarna 385xp bearings & seals
« on: November 03, 2015, 12:03:30 am »
What size bears & seals are used for the mains on that saw? looking to see if the bearing houses would carry one of OEM size/tolerance/quality in a better brand than OEM

Share on Facebook Share on Twitter


Offline exSW

  • 4 cube
  • **
  • Posts: 47
  • Karma: 8
Re: Husqvarna 385xp bearings & seals
« Reply #1 on: November 03, 2015, 12:12:17 am »
Just went through this on a Jred 2186(same saw,diff accessories). The flywheel side is common. But near as I could tell the pto bearing/seal combo is proprietary .

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2111
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 385xp bearings & seals
« Reply #2 on: November 03, 2015, 03:48:31 am »
Yep.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22126
  • Karma: 551
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 385xp bearings & seals
« Reply #3 on: November 03, 2015, 12:23:57 pm »
Yep pto there was a older set up used by poulan in 505 445 425 but it has updated to the 385 390 combo.  SOL on this one we are.
REDNECK Saw Repair Getter Done

Offline exSW

  • 4 cube
  • **
  • Posts: 47
  • Karma: 8
Re: Husqvarna 385xp bearings & seals
« Reply #4 on: November 03, 2015, 02:20:23 pm »
$40.00. First thing I suggested to Definitive Dave when he asked.

 

Related Topics

  Subject / Started by Replies Last post
15 Replies
751 Views
Last post September 24, 2013, 07:23:56 pm
by Cut4fun .
12 Replies
573 Views
Last post August 31, 2013, 07:28:45 pm
by 660magnum
24 Replies
905 Views
Last post October 23, 2014, 12:22:01 pm
by Cut4fun .
2 Replies
189 Views
Last post October 27, 2013, 09:09:17 am
by brokenbudget
18 Replies
507 Views
Last post November 11, 2013, 09:19:48 am
by KilliansRedLeo
0 Replies
66 Views
Last post January 11, 2014, 01:51:50 pm
by KilliansRedLeo
3 Replies
2077 Views
Last post June 08, 2019, 10:22:48 am
by Cut4fun .
10 Replies
463 Views
Last post June 21, 2016, 03:18:11 pm
by Giles
2 Replies
298 Views
Last post July 08, 2016, 12:27:43 pm
by Acel83
2 Replies
111 Views
Last post February 28, 2018, 01:24:21 pm
by Cut4fun .