« previous next »
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17   Go Down

Author Topic: Husqvarna 394  (Read 7091 times)

0 Members and 14 Guests are viewing this topic.

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171

    • Total Badges: 31
    Badges: (View All)
    Level 6 Sixth year Anniversary Fifth year Anniversary 1000 Posts Fourth year Anniversary 500 Posts
Re: husqvarna 394
« Reply #120 on: October 25, 2015, 09:01:19 pm »
You'll end up with plenty of good carb choices.
Logged

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: husqvarna 394
« Reply #121 on: November 07, 2015, 07:16:36 pm »
Finally figured out why I still could not gain any rpm on the top. I put on a oem ignition module. Problem fixed. Guess I have a good wj-70. Saw idles better and picks up rpm faster. I should have known to get a oem one from the start. Found the one I got on eBay for $77 shipped. I am going to run it threw some wood on Monday.
Logged
FEAR NO TREE. FEAR GOD.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23734
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: husqvarna 394
« Reply #122 on: November 07, 2015, 08:11:21 pm »
Aftermarket 394 coil was holding it back?  I was just looking at them the other day while shopping for parts.
Logged

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD

    • Total Badges: 36
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Level 6
Re: husqvarna 394
« Reply #123 on: November 07, 2015, 08:34:40 pm »
Yes, i guess that is what you get for $30. The saw sounds different. And will go lean on the high side with the high speed screw. It always seemed to just be over fueled. That is why I bought another carb. And that did not fix it. Then I knew it had to be the module.
Logged
FEAR NO TREE. FEAR GOD.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23734
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: husqvarna 394
« Reply #124 on: December 20, 2015, 10:09:47 pm »
Quote from: srcarr52 on June 24, 2015, 04:54:58 pm

That sounds about right,

This saw built by you sounds right too.  :o

Logged

Offline srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 94
  • Location: IA

    • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 Second year Anniversary 100 Posts Topic Starter Search
Re: husqvarna 394
« Reply #125 on: December 21, 2015, 11:18:28 am »
Quote from: Cut4fun . on December 20, 2015, 10:09:47 pm
This saw built by you sounds right too.  :o

It was a good saw but 395 FTW!

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23734
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: husqvarna 394
« Reply #126 on: December 21, 2015, 12:47:52 pm »
Dang!  you put a tach on that to see what it was pulling through that cut. Sounds sweeeeeeeeet
Logged

Offline Spruce_Goose

  • 3 cube
  • *
  • Posts: 21
  • Karma: 1

    • Total Badges: 8
    Badges: (View All)
    One year Anniversary Karma Level 2 10 Posts Topic Starter First Post
Re: husqvarna 394
« Reply #127 on: January 06, 2016, 06:46:49 pm »
Quote
Wj 39 or wj 69 can be made to fit with a few linkage changes from what I remember.

My 394 has the WJ-39-1, I think its stock for older ones. So no changes even needed. The WJ-39-1, I believe, has essentially been replaced by WJ-71-1

Logged

Offline srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 94
  • Location: IA

    • Total Badges: 22
    Badges: (View All)
    Third year Anniversary Level 5 Second year Anniversary 100 Posts Topic Starter Search
Re: husqvarna 394
« Reply #128 on: January 07, 2016, 10:13:25 am »
Quote from: Spruce_Goose on January 06, 2016, 06:46:49 pm
Quote
Wj 39 or wj 69 can be made to fit with a few linkage changes from what I remember.

My 394 has the WJ-39-1, I think its stock for older ones. So no changes even needed. The WJ-39-1, I believe, has essentially been replaced by WJ-71-1


WJ-39 is the normal 394 carb.
WJ-70 is the late model EPA compliant carb.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23734
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

    • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Husqvarna 394
« Reply #129 on: February 08, 2018, 06:03:57 pm »
1993 husqvarna 394 low top in.  Need a few parts.   503524401

Need to pull carb to see

WJ-70-1    K10-WJ

WJ-71-1   K13-WJ **OBSOLETE/USE K10-WJ**

WJ-39-1    K10-WJ

Logged
Pages: 1 ... 8 9 10 11 12 [13] 14 15 16 17   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
9 Replies
986 Views 		Last post April 09, 2011, 09:18:24 pm
by Cut4fun .
2 Replies
650 Views 		Last post March 04, 2012, 02:35:58 pm
by Cut4fun .
Husqvarna 455

Started by Cut4fun « 1 2 3 4 » Husqvarna

34 Replies
4961 Views 		Last post November 01, 2023, 03:47:53 pm
by Cut4fun .
9 Replies
708 Views 		Last post March 23, 2013, 06:59:06 pm
by Magnus
2 Replies
549 Views 		Last post April 27, 2013, 04:08:24 pm
by Old Iron Logging
11 Replies
1120 Views 		Last post January 01, 2015, 10:09:19 pm
by farmboy
Husqvarna 350

Started by rob67 « 1 2 ... 9 10 » Husqvarna

93 Replies
3645 Views 		Last post December 05, 2015, 10:18:36 pm
by Cut4fun .
Husqvarna 365 OE

Started by alsled « 1 2 ... 6 7 » Husqvarna

61 Replies
2560 Views 		Last post June 27, 2023, 10:47:27 am
by Cut4fun
0 Replies
185 Views 		Last post March 25, 2023, 09:23:29 am
by Cut4fun
0 Replies
158 Views 		Last post April 12, 2023, 10:06:37 am
by Cut4fun .