Author Topic: Husqvarna 435 bar mount stud  (Read 137 times)

0 Members and 0 Guests are viewing this topic.

Offline Bob

  • 3 cube
  • *
  • Posts: 16
  • Karma: 0
Husqvarna 435 bar mount stud
« on: April 02, 2015, 01:26:39 pm »
I was given a husky 435 and as I was putting the clutch cover back on the mounting stud for the bar went back into the saw case and is no longer sticking out.
Anyone know how to fix this and why the stud would disappear? How does  it attach to the case? I have owned a lot of saws over the years can't recall this problem ever happening.
Thank you

Share on Facebook Share on Twitter


Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Husqvarna 435 bar mount stud
« Reply #1 on: April 02, 2015, 03:56:05 pm »
Most bar studs are just pressed into the case.

Reach in the oil tank and push the stud out.

When putting the nut on - make sure the flats on the stud align with the stops inside the oil tank.
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21948
  • Karma: 533
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 435 bar mount stud
« Reply #2 on: April 02, 2015, 04:12:42 pm »
I use a telescoping magnet to help me guide bar studs back into case holes.  From outside the bar oil tank cap area.

REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21948
  • Karma: 533
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 435 bar mount stud
« Reply #3 on: April 02, 2015, 04:14:34 pm »
Seen this on feebay

Husqvarna Jonsered Chainsaw Bar Stud 2240 225 435 435E 445 445E 440E

REDNECK Saw Repair Getter Done

Offline wild262

  • 6 cube
  • ****
  • Posts: 161
  • Karma: 29
Re: Husqvarna 435 bar mount stud
« Reply #4 on: April 03, 2015, 09:25:53 am »
Also on some saws like the 350 series, theres a metal channel support (I call it) that helps distribute the pressure against the case that is between the stud and case.   If your saw has it, then it should still be in there providing the other stud hasn't fallen out prior.   I use a long locking 8" pair of forceps to re-position these.   I had a 435 once, but never had any problems with it, and was a good saw for light limbing.  Hope this helps ya.  :)

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
1397 Views
Last post June 17, 2011, 11:35:12 pm
by SawTroll
stihl bar stud repair

Started by mweba « 1 2 » Stihl

12 Replies
2698 Views
Last post September 09, 2019, 09:42:41 am
by joe_indi
3 Replies
190 Views
Last post August 17, 2013, 10:20:27 pm
by cowroy
1 Replies
163 Views
Last post November 05, 2013, 12:38:23 am
by Eccentric
10 Replies
231 Views
Last post December 31, 2013, 06:13:12 pm
by 3000 FPS
Broken Bar Stud 039

Started by BSW « 1 2 » Stihl

11 Replies
280 Views
Last post February 23, 2014, 04:08:33 am
by bustedknuckles
5 Replies
586 Views
Last post September 03, 2014, 11:53:37 pm
by 3000 FPS
7 Replies
302 Views
Last post September 02, 2014, 03:29:39 pm
by Nathaniel Vansickle
13 Replies
757 Views
Last post October 23, 2019, 10:56:27 am
by Cut4fun .
0 Replies
82 Views
Last post September 09, 2019, 09:38:40 am
by joe_indi