Author Topic: Husqvarna 455 rancher Oil issues  (Read 2853 times)

0 Members and 0 Guests are viewing this topic.

Offline didal

  • 3 cube
  • *
  • Posts: 8
  • Karma: 0
Re: Husqvarna 455 rancher Oil issues
« Reply #10 on: December 08, 2012, 09:31:46 am »
And one more .....

Offline didal

  • 3 cube
  • *
  • Posts: 8
  • Karma: 0
Re: Husqvarna 455 rancher Oil issues
« Reply #11 on: December 08, 2012, 09:43:43 am »
Maybe a dumb question, but should the alien screw that holds the pump in place be tight or just a little lose?

Offline man of stihl

  • Nitro Hotsaw
  • *******
  • Posts: 1219
  • Karma: 71
  • NW PA
  • Location: nw pennsylvania
Re: Husqvarna 455 rancher Oil issues
« Reply #12 on: December 08, 2012, 09:55:03 am »
Nice pics. Looks like its pumping enough oil. I would say the allen screw needs to be tight. Why do you ask?
Ron

Offline didal

  • 3 cube
  • *
  • Posts: 8
  • Karma: 0
Re: Husqvarna 455 rancher Oil issues
« Reply #13 on: December 08, 2012, 09:59:10 am »
I asked because I noticed it was a little loose when I replaced the plastic pinion - so I made it tight ... I just went checked over the bar oil holes again, and they are not clogged.

Yes it does look like plenty of oil, now if it would only go where it is supposed to!  :)

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4087
  • Karma: 165
  • OHIO REDNECK
Re: Husqvarna 455 rancher Oil issues
« Reply #14 on: December 08, 2012, 12:29:51 pm »
There is a rubber cup coming out of the oil tank. The oiler must line up in it when set in place. The rubber cub on the outside must line up on top when everything is done and closed up.

Check to make sure the rubber cup coming out of the oil tank is not pinched and not all the way out.



Remove oil pump etc to see this clearly.
REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
46 Replies
6084 Views
Last post July 31, 2011, 09:45:54 am
by farmboy
11 Replies
4539 Views
Last post February 08, 2013, 07:37:59 pm
by Hill Billy
5 Replies
760 Views
Last post February 21, 2012, 01:29:32 pm
by 660magnum
27 Replies
378 Views
Last post January 22, 2014, 09:23:12 pm
by SawTroll
4 Replies
383 Views
Last post May 29, 2018, 07:10:01 am
by Cut4fun .
5 Replies
231 Views
Last post November 15, 2016, 08:11:48 pm
by 3000 FPS
1 Replies
110 Views
Last post June 26, 2018, 07:45:18 pm
by Cut4fun .
1 Replies
103 Views
Last post April 01, 2020, 08:41:57 am
by Cut4fun .
2 Replies
153 Views
Last post August 23, 2019, 09:30:07 pm
by ray benson
2 Replies
19 Views
Last post September 30, 2020, 07:24:12 am
by Spike60