Author Topic: Husqvarna 455 Stalls When Hot  (Read 146 times)

0 Members and 0 Guests are viewing this topic.

Offline dudechuck

  • 4 cube
  • **
  • Posts: 47
  • Karma: 2
Husqvarna 455 Stalls When Hot
« on: August 13, 2019, 07:33:28 am »
I searched but got no results and I know this has been asked before. But my Husqvarna 455 starts great and runs great until it gets hot after about 15 minutes of run time.

I have changed spark plug, fuel filter, air filter, re-tuned ( which I am not good at) and a couple more things that I cannot remember. After 15 minutes the chain will bog down as if what I am cutting is to much for it. Then after another minute or so it turns off. I have no problem starting it but it does the same thing right away. Let it rest maybe 20 minutes it will cut fine then repeat the above.

Any ideas?   

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22584
  • Karma: 591
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 455 Stalls When Hot
« Reply #1 on: August 13, 2019, 07:49:59 am »
Just a WAG, I was thinking coil going out. Also have you ever put a fresh carb kit in. Stiff diaphragms, but that shows up during a cut. Then take out of cut then does in cut again.
REDNECK Saw Repair Getter Done

Offline dudechuck

  • 4 cube
  • **
  • Posts: 47
  • Karma: 2
Re: Husqvarna 455 Stalls When Hot
« Reply #2 on: August 13, 2019, 08:07:02 am »
Full carb build last summer.

Offline trail twister

  • 5 cube
  • ***
  • Posts: 107
  • Karma: 18
Re: Husqvarna 455 Stalls When Hot
« Reply #3 on: August 13, 2019, 06:45:16 pm »
Chain bogs down, Notice any engine performance decline before that?

I woild check the chain brake spring if not.

:D       Al

 

Related Topics

  Subject / Started by Replies Last post
9 Replies
537 Views
Last post April 09, 2011, 09:18:24 pm
by Cut4fun .
7 Replies
1732 Views
Last post November 20, 2011, 03:28:21 pm
by SawTroll
Husqvarna 66

Started by Cut4fun « 1 2 3 » Husqvarna

24 Replies
2276 Views
Last post June 19, 2020, 05:49:02 am
by Spike60
3 Replies
235 Views
Last post March 21, 2011, 05:40:40 pm
by Kjell S
0 Replies
243 Views
Last post April 03, 2011, 06:59:07 pm
by adam32
2 Replies
225 Views
Last post March 04, 2012, 02:35:58 pm
by Cut4fun .
10 Replies
952 Views
Last post January 27, 2013, 09:59:58 pm
by 3000 FPS
2 Replies
718 Views
Last post March 10, 2016, 02:54:55 pm
by 660magnum
0 Replies
409 Views
Last post November 26, 2016, 02:35:22 pm
by weimedog
0 Replies
155 Views
Last post October 29, 2017, 09:09:27 pm
by weimedog