Author Topic: Husqvarna 66  (Read 1992 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21945
  • Karma: 532
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 66
« Reply #20 on: June 04, 2020, 12:36:24 pm »
Found a few more old pics of the husqvarna 66 1989 saw




REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Spike60

  • Piped Saw
  • *****
  • Posts: 329
  • Karma: 104
  • Location: Ulster County, NY
Re: Husqvarna 66
« Reply #21 on: June 08, 2020, 01:16:54 pm »
I finally got one of these since the last time we talked about them. Low hours and in good shape. I'll try and get some pics up at some point.
Husqvarna-Jonsered

Ashokan Turf and Timber

845-657-6395
Like Like x 2 View List

Offline president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: Husqvarna 66
« Reply #22 on: June 08, 2020, 01:33:41 pm »
I have a cylinder,and the intake port is much smaller than my 266se
and if its open port potential power would suffer.My 162 is the same potr
openings of the 266se
Informative Informative x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21945
  • Karma: 532
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 66
« Reply #23 on: June 09, 2020, 07:52:51 am »
I have a cylinder,and the intake port is much smaller than my 266se
and if its open port potential power would suffer.My 162 is the same potr
openings of the 266se

No clue here. Never pulled the open port cylinder. Went straight to a collector overseas somewhere.  Thinking it was Finland. Cant recall for sure now.
REDNECK Saw Repair Getter Done
Like Like x 1 View List

Offline Spike60

  • Piped Saw
  • *****
  • Posts: 329
  • Karma: 104
  • Location: Ulster County, NY
Re: Husqvarna 66
« Reply #24 on: June 19, 2020, 05:49:02 am »
Intake port really shouldn't be smaller than a 266. Actually ought to be bigger. That 66 top end is the same as used on the 268 open port and 268K cut off saws. Uses the same intake block as the 268/272. Possible that different cylinder sources could be the deal. Gilardoni maybe? My 66 is from the Tomos factory, and I've never taken mine apart either.
Husqvarna-Jonsered

Ashokan Turf and Timber

845-657-6395
Like Like x 1 Informative Informative x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
12 Replies
621 Views
Last post February 11, 2013, 04:22:19 pm
by Cut4fun
25 Replies
3864 Views
Last post February 03, 2013, 01:45:30 pm
by Cut4fun .
6 Replies
722 Views
Last post June 27, 2017, 08:30:17 pm
by Cut4fun .
0 Replies
128 Views
Last post March 30, 2016, 07:10:38 pm
by mikehonda
4 Replies
264 Views
Last post April 12, 2016, 06:30:34 pm
by dannyupsolate
4 Replies
338 Views
Last post November 07, 2016, 05:46:56 pm
by oldpro
2 Replies
274 Views
Last post May 15, 2016, 04:59:09 am
by Eccentric
20 Replies
965 Views
Last post March 21, 2018, 10:47:30 am
by Cut4fun .
4 Replies
330 Views
Last post November 23, 2016, 02:23:26 am
by georgehopson
1 Replies
206 Views
Last post April 10, 2017, 11:29:19 am
by 3000 FPS