Author Topic: Husqvarna Crank bearings and crankshaft installation  (Read 2729 times)

0 Members and 0 Guests are viewing this topic.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
+1 on what Kevin said above! Check it out!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline David Young

  • 5 cube
  • ***
  • Posts: 133
  • Karma: 16
Seen the big end go out on a good bit here. Check her out David.   I only used new oem kits or used good. 
Some folks say they have had good luck with some of the aftermarket ones, but I was scared to do it for a saw I would evidently sell down the road. If I had kept them I might have tried one.

I hear ya,

if I ever did let a saw with afm parts out of my hands, I feel ok as long as I disclose what parts are used.
Crank well too much can go wrong.  I don't know if I would try it.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Looks like the ring caught something on the intake side, odd unless it has finger ports?

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
There is also a chance that the locating pin in the ring groove backed out since I cannot see it in the picture. Spoke to David last evening, he believes that the big end bearings let go. More up/down play than in other saw bottom ends he has. He is sending the case and crank to me to be replaced. I'll put up some pics when it arrives.
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 24232
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
I may have a bad big end crank paper weight in the barn if anyone needs to view till then.

 

Related Topics

  Subject / Started by Replies Last post
15 Replies
2477 Views
Last post September 24, 2013, 07:23:56 pm
by Cut4fun .
41 Replies
4696 Views
Last post May 09, 2019, 07:07:16 pm
by HUSKY KEV
12 Replies
1815 Views
Last post August 31, 2013, 07:28:45 pm
by 660magnum
2 Replies
981 Views
Last post October 27, 2013, 09:09:17 am
by brokenbudget
18 Replies
2695 Views
Last post November 11, 2013, 09:19:48 am
by KilliansRedLeo
0 Replies
598 Views
Last post January 11, 2014, 01:51:50 pm
by KilliansRedLeo
Crank bearings

Started by jmester « 1 2 » Stihl

12 Replies
1610 Views
Last post July 24, 2015, 07:14:47 pm
by 67L36Driver
4 Replies
1233 Views
Last post March 10, 2016, 11:06:21 am
by 660magnum
3 Replies
1261 Views
Last post March 18, 2016, 09:02:35 am
by Jason K
10 Replies
1816 Views
Last post June 21, 2016, 03:18:11 pm
by Giles