Author Topic: Husqvarna T540xp Demo  (Read 4508 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21952
  • Karma: 535
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna T540xp Demo
« Reply #50 on: January 28, 2014, 04:05:19 pm »
Many Thanks to Randy aka Mastermind for getting me the PHO weights.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna T540xp Demo
« Reply #51 on: January 28, 2014, 07:34:12 pm »
Handled the 540XPT at the dealership today.  Just looked it over and 'one handed' it around a bit.  Also checked out a 338XPT and an Echo CS355T at the same dealership.  Both the Echo and the 338XPT were noticeably lighter and more compact. 

I haven't handled a 200T is about six months...........so my 'calibrated arm' wasn't able to really judge where the Stihl fits along with these other tophandles.  From (dim) memory I'd say the Stihl feels a tad lighter than the 540XPT (and about as 'bulky'), but heavier than the Echo and the 338XPT.

Would like to run all these tophandles side by side in the same wood............with fresh loops of Stihl 63PS on 'em.   That's all academic for me however.  I'm not a pro, and likely would never buy a new tophandle.  My old Poulan S25 saws do what I need a tophandle to do for me.  I may still be getting that 335XPT California from my buddy if I feel the need for a more modern tophandle saw.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21952
  • Karma: 535
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna T540xp Demo
« Reply #52 on: January 28, 2014, 08:00:07 pm »
Aaron I have husqvarna 335 338 service manual in pdf 54 pages if you need it down the road.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna T540xp Demo
« Reply #53 on: January 28, 2014, 08:49:34 pm »
Aaron I have husqvarna 335 338 service manual in pdf 54 pages if you need it down the road.

Thank you Kevin.   Please send it to me.  I'll probably end up with that 335XPT-C.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: Husqvarna T540xp Demo
« Reply #54 on: January 29, 2014, 02:17:43 pm »
Aaron I have husqvarna 335 338 service manual in pdf 54 pages if you need it down the road.

Thank you Kevin.   Please send it to me.  I'll probably end up with that 335XPT-C.

Just sent.
REDNECK Saw Repair

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna T540xp Demo
« Reply #55 on: January 29, 2014, 02:35:39 pm »
Aaron I have husqvarna 335 338 service manual in pdf 54 pages if you need it down the road.

Thank you Kevin.   Please send it to me.  I'll probably end up with that 335XPT-C.

Just sent.

Received and saved.  Thanks Kevin!
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna T540xp Demo
« Reply #56 on: January 31, 2014, 08:57:06 pm »
Many Thanks to Randy aka Mastermind for getting me the PHO weights (540XPT).




Brad just posted this MS201T PHO weight picture in another thread.  Looks like they're pretty close.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: Husqvarna T540xp Demo
« Reply #57 on: January 31, 2014, 09:03:19 pm »
Exactly why I am kicking myself for selling my 338 now.  I want lighter not heaver for 1 handing.
REDNECK Saw Repair

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna T540xp Demo
« Reply #58 on: January 31, 2014, 09:06:03 pm »
Exactly why I am kicking myself for selling my 338 now.  I want lighter not heaver for 1 handing.

Have you checked out the Echo CS355T?
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4067
  • Karma: 162
  • OHIO REDNECK
Re: Husqvarna T540xp Demo
« Reply #59 on: January 31, 2014, 09:16:37 pm »
Read on it alot. Seems the same weight as the other 2 that gained weight. I want lighter. Not worried about big cuts.
REDNECK Saw Repair

 

Related Topics

  Subject / Started by Replies Last post
7 Replies
1686 Views
Last post November 20, 2011, 03:28:21 pm
by SawTroll
Husqvarna 66

Started by Cut4fun « 1 2 3 » Husqvarna

24 Replies
1995 Views
Last post June 19, 2020, 05:49:02 am
by Spike60
105 Replies
7163 Views
Last post July 15, 2012, 08:40:15 am
by SawTroll
0 Replies
232 Views
Last post April 03, 2011, 06:59:07 pm
by adam32
Husqvarna 45

Started by Cut4fun . « 1 2 » Husqvarna

10 Replies
866 Views
Last post May 21, 2014, 10:08:28 am
by SawTroll
Husqvarna 455

Started by Cut4fun « 1 2 3 4 » Husqvarna

31 Replies
2558 Views
Last post April 02, 2019, 10:58:15 am
by Cut4fun .
28 Replies
526 Views
Last post October 25, 2018, 02:44:19 am
by Eccentric
1 Replies
140 Views
Last post December 01, 2015, 11:24:23 pm
by Cut4fun .
2 Replies
315 Views
Last post February 21, 2017, 01:22:50 pm
by Cut4fun .
5 Replies
153 Views
Last post October 16, 2018, 03:45:23 pm
by Cut4fun .