« previous next »
Pages: [1]   Go Down

Author Topic: Industry numbers for seals  (Read 808 times)

0 Members and 0 Guests are viewing this topic.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Industry numbers for seals
« on: May 21, 2014, 10:33:14 am »
I need industry numbers for Husqvarna crankshaft seals
503260301 clutch side seal
505275719 flywheel side seal

Failing that the metric sizes would do if anyone has them.

Want to find a source for Viton seals as well as standard double lip with garter spring.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Share on Facebook Share on Twitter

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Industry numbers for seals
« Reply #1 on: May 21, 2014, 07:02:27 pm »
I measure the seals as 15 X 26 X 4.5 for the flywheel side
and 17.5 X 26 X 4.5 for the clutch side.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Industry numbers for seals
« Reply #2 on: May 21, 2014, 09:29:02 pm »
Agree, thank you Jim!
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172
Re: Industry numbers for seals
« Reply #3 on: May 21, 2014, 10:11:38 pm »
Are you guys measuring the seal or crank?
Logged

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Industry numbers for seals
« Reply #4 on: May 21, 2014, 10:15:29 pm »
I measured a crank on the flywheel side and a sleeve on the clutch side.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Industry numbers for seals
« Reply #5 on: May 22, 2014, 04:05:15 am »
I was trying to get an industry number for the seals used in a 372xp. I want to find a source for the seals in bulk instead of a set at a time. I would also like to find non-Chinese made.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Industry numbers for seals
« Reply #6 on: May 22, 2014, 07:49:59 am »
I ran into a situation that I still have not figured out. I was rebuilding a 372 and all was going well, until the pressure/vac test. I had a leak on the clutch side. Had replaced the bearings, case gasket and clutch side o-ring and both seals. Leak was so bad saw would not hold any pressure at all.  Needless to say I immediately suspected the clutch side seal and that was the leak. Pulled it and installed a new one, saw still leaked. Could not tell if the leak was coming from between the crankshaft and the seal or between the seal and the case. But that ran me out of seals. Even replaced the o-ring.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline jmester

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2106
  • Karma: 171
  • Location: MD
Re: Industry numbers for seals
« Reply #7 on: May 22, 2014, 08:02:34 am »
Do you put any sealant like stihls dirko around the outer edge of the seal? Where the metal meets the case. Stihl recommends that you do it that way in the service manual. I have done it that way on all the seals that I do weather stihl or husky. Have had good luck with it. Just a thought.
Logged
FEAR NO TREE. FEAR GOD.

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: Industry numbers for seals
« Reply #8 on: May 22, 2014, 08:06:07 am »
Good idea, I will try it today, and let you know when the sealer sets up. Thanks!
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
1 Replies
5307 Views 		Last post May 09, 2011, 09:04:07 pm
by mcbob
5 Replies
1712 Views 		Last post January 18, 2013, 03:51:05 pm
by 660magnum
5 Replies
765 Views 		Last post January 22, 2014, 02:46:36 pm
by danders
11 Replies
1561 Views 		Last post December 30, 2018, 08:12:28 pm
by Cut4fun .
4 Replies
588 Views 		Last post August 02, 2014, 06:07:44 pm
by pigpen60
8 Replies
1561 Views 		Last post October 14, 2014, 07:17:32 am
by Trang77
9 Replies
664 Views 		Last post December 07, 2017, 11:36:32 am
by Cut4fun .
2 Replies
2220 Views 		Last post March 20, 2016, 01:15:19 pm
by 660magnum
5 Replies
7452 Views 		Last post September 10, 2024, 09:08:57 am
by Cut4fun .
1 Replies
902 Views 		Last post February 28, 2021, 10:07:51 am
by ray benson