« previous next »
Pages: 1 [2]   Go Down

Author Topic: new Metal Clamp 350 353 346 etc  (Read 267 times)

0 Members and 0 Guests are viewing this topic.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: new Metal Clamp 350 353 346 etc
« Reply #10 on: March 17, 2015, 09:41:52 pm »
I have the tools as I've re-done a few CV joints but they are not expensive and are on the turn around rack by the counter at the NAPA store.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: new Metal Clamp 350 353 346 etc
« Reply #11 on: March 18, 2015, 12:56:56 am »
Quote from: 660magnum on March 17, 2015, 09:41:52 pm
I have the tools as I've re-done a few CV joints but they are not expensive and are on the turn around rack by the counter at the NAPA store.

Interesting.  May still be a good way to go.  Here's a couple examples of those pliers from Napa.  Cheap, and not quite so cheap.  Might also be able to borrow them from an auto parts store with a deposit.  I borrowed a disc brake caliper tool set from my local O'Reilly Auto Parts store last month.  Just had to pay a deposit (retail value of the tool set) that I got back...

http://www.napaonline.com/Catalog/CatalogItemDetail.aspx/Pliers-Ear-Type-CV-Joint-Boot-Clamp-Pliers/_/R-BK_7769244_0006392255

http://www.napaonline.com/Catalog/CatalogItemDetail.aspx/CV-Joint-Boot-Clamp-Pliers/_/R-SER3955_0006402481
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: new Metal Clamp 350 353 346 etc
« Reply #12 on: March 18, 2015, 06:00:03 am »
I had to have two different kinds of pliers. I must have done OK for some of those vehicles were driven another 100K after I cleaned, re-packed and rebooted the CV joints on the half shafts.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Online Fishnuts2

  • 4 cube
  • **
  • Posts: 57
  • Karma: 15
Re: new Metal Clamp 350 353 346 etc
« Reply #13 on: March 29, 2015, 12:53:46 pm »
These are a lot harder to get locked than first appears. I did my 359 and it took me about 10 tries with 2 different styles of pliers. That hood part doesn't snap over, instead it just raised up.

I had already promised my son in law that I'd do his 359 so next I'm going to try a needle-nosed vice grip. The CV tool seems good too.


Sent from my iPhone using Tapatalk
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22011
  • Karma: 541
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: new Metal Clamp 350 353 346 etc
« Reply #14 on: March 29, 2015, 01:51:20 pm »
When I used the needle nose vise grips putting on 2150 cylinder it only took 1 try.  Thats the trick to it IMO.
Logged
REDNECK Saw Repair Getter Done
Pages: 1 [2]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
3 Replies
1042 Views 		Last post January 10, 2018, 07:47:10 am
by Cut4fun .
1 Replies
704 Views 		Last post May 09, 2012, 08:32:08 pm
by Al Smith
12 Replies
561 Views 		Last post December 28, 2012, 07:52:28 pm
by Al Smith
2 Replies
427 Views 		Last post February 10, 2013, 08:09:53 pm
by Al Smith
12 Replies
177 Views 		Last post January 05, 2014, 10:21:27 pm
by jmester
10 Replies
321 Views 		Last post January 10, 2014, 12:35:53 pm
by Cut4fun .
18 Replies
505 Views 		Last post December 17, 2014, 10:47:07 am
by srcarr52
28 Replies
318 Views 		Last post May 28, 2015, 11:35:33 pm
by 660magnum
15 Replies
1462 Views 		Last post December 15, 2018, 09:05:17 am
by HUSKY KEV
1 Replies
149 Views 		Last post September 18, 2017, 08:38:44 pm
by 3000 FPS