Author Topic: Husky 460 oil not getting onto bar  (Read 373 times)

0 Members and 16 Guests are viewing this topic.

Offline JakesHusky

  • pruner
  • *
  • Posts: 2
  • Karma: 0

  • Total Badges: 8
    Badges: (View All)
    Combination Topic Starter Level 2 First Post Linux User Mobile User
Husky 460 oil not getting onto bar
« on: November 01, 2019, 03:11:55 pm »
Hello all,

so i have a new little problem on my 460 Rancher. After a good cleaning and getting ready to go cut firewood, i put my bar and chain back on, and gave it a quick test and i noticed that barely any oil at all was slinging off the chain, and instead it was running down the side of where the bar mounts. I Cleaned out the hole and guide slot on the bar, and also tried another bar and fired it up again. same problem. It appears almost that the bar isnt sitting flush up against the little oval shaped peice that the oil comes out of so it just drools down instead of going into the hole on the bar. At least thats all i can think of. plenty of oil is pumping but its not going where it should. If anybody knows what the oval shaped peice is called i would appreciate that info, and if anyone has an idea of another possible cause that would be great as well.

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: oil not getting onto bar
« Reply #1 on: November 02, 2019, 08:26:47 am »
husqvarna 460 rancher ipl  https://www.hsqintec.sk/vykres/455e460-09.pdf

Think your talking about part #14 in IPL. Check to make sure the IPL I picked goes along with year of your saw 2009. Sometimes they update them and change a part. Then a new IPL comes out.

Offline JakesHusky

  • pruner
  • *
  • Posts: 2
  • Karma: 0

  • Total Badges: 8
    Badges: (View All)
    Combination Topic Starter Level 2 First Post Linux User Mobile User
Re: Husky 460 oil not getting onto bar
« Reply #2 on: November 02, 2019, 11:37:24 am »
Sorry for my lack of knowledge, but what is the IPL. I do think that is the part I'm talking about though. but out of curiosity what might make that part not seal against the bar, so I can avoid this problem in the future. thank you

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23708
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair

  • Total Badges: 53
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Level 8 Apple User Eighth year Anniversary 20000 Posts
Re: Husky 460 oil not getting onto bar
« Reply #3 on: November 02, 2019, 01:36:42 pm »
On a stihl 029 which had bar shoulders. The stud was out some not allowing bar to set flush. With yours I doublt this is the case being small mount husky 455 460 studs dont use shoulders.

Check and see if the area is heat warped or bar bent etc. Can only guess online.
Like Like x 1 View List

 

Related Topics

  Subject / Started by Replies Last post
husky 55 help

Started by mrbb « 1 2 » Husqvarna

15 Replies
1343 Views
Last post July 29, 2013, 07:59:33 am
by mrbb
2 Replies
249 Views
Last post March 29, 2014, 06:23:35 pm
by Cut4fun .
3 Replies
501 Views
Last post August 01, 2014, 09:30:09 am
by hadji
8 Replies
778 Views
Last post August 29, 2014, 11:18:29 am
by alex matthew
3 Replies
565 Views
Last post August 30, 2014, 09:00:06 am
by Cut4fun
7 Replies
631 Views
Last post August 31, 2014, 04:35:30 pm
by farmboy
1 Replies
371 Views
Last post September 25, 2014, 04:34:24 pm
by ChipsAhoy
Husky 50

Started by 3000 FPS « 1 2 3 » Husqvarna

24 Replies
1206 Views
Last post December 27, 2014, 08:56:13 pm
by miltonsain
15 Replies
1321 Views
Last post January 23, 2015, 02:03:24 pm
by Bluegill
2 Replies
326 Views
Last post December 14, 2022, 02:31:59 pm
by jfulford1