Author Topic: 338 oiler  (Read 684 times)

0 Members and 0 Guests are viewing this topic.

Offline gunrac

  • 4 cube
  • **
  • Posts: 55
  • Karma: 5
  • Location: Marion Ohio
Re: 338 oiler
« Reply #20 on: March 10, 2014, 11:35:51 am »
The piston pump needs to be slid back in the pump housing to allow for the control bolt to thread into the pump housing. The round portion above the threads on the control bolt rides on the end of the pump shaft  near the splined portion. Once the control bolt fell out the piston pump slid forward enough to not let the control bolt slide in. May be I am missing what you are asking.

That makes perfect since. Will this take a tear down to do? What kind of a job is it to slide it back?

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 338 oiler
« Reply #21 on: March 10, 2014, 12:05:28 pm »
Not a big deal to push it back but you will have to remove the clutch drum, clutch and worm wheel. So you can get to the pump shaft teeth that the worm wheel engages. You can then push the shaft in the desired direction with a dental pick!

Got a idea just now. From looking at this 338 oiler  pic.
Separate the part that screws into the case.  Then put the part in the case first then screw  the adjuster part back in the other part once installed back in the case.
 Remember I am just WAGing here.


"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline gunrac

  • 4 cube
  • **
  • Posts: 55
  • Karma: 5
  • Location: Marion Ohio
Re: 338 oiler
« Reply #22 on: March 11, 2014, 04:07:09 pm »
Not a big deal to push it back but you will have to remove the clutch drum, clutch and worm wheel. So you can get to the pump shaft teeth that the worm wheel engages. You can then push the shaft in the desired direction with a dental pick!

I done what you suggested, it fell right together.....but the worm wheel was pretty well ate up.
Replaced it...all is good........thx guys

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 338 oiler
« Reply #23 on: March 11, 2014, 04:45:25 pm »
Glad we could help !
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4118
  • Karma: 170
  • OHIO REDNECK
Re: 338 oiler
« Reply #24 on: March 11, 2014, 04:47:44 pm »
Not a big deal to push it back but you will have to remove the clutch drum, clutch and worm wheel. So you can get to the pump shaft teeth that the worm wheel engages. You can then push the shaft in the desired direction with a dental pick!


Good deal gunrac.


I enjoyed learning more about these saws from the side lines.  The above was neat to know too.
REDNECK Saw Repair

Offline gunrac

  • 4 cube
  • **
  • Posts: 55
  • Karma: 5
  • Location: Marion Ohio
Re: 338 oiler
« Reply #25 on: March 11, 2014, 05:00:52 pm »
Not a big deal to push it back but you will have to remove the clutch drum, clutch and worm wheel. So you can get to the pump shaft teeth that the worm wheel engages. You can then push the shaft in the desired direction with a dental pick!




Good deal gunrac.


I enjoyed learning more about these saws from the side lines.  The above was neat to know too.

Easy little tricks to everything, nice to find a forum where there are good people that will share them.
I need to get that other saw to you, so I quit robbing parts off it....I been sick the last several days, bit better now. Maybe get hooked up w/you this weekend....

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4118
  • Karma: 170
  • OHIO REDNECK
Re: 338 oiler
« Reply #26 on: March 11, 2014, 05:13:22 pm »
Still betting just the fulcrum is a bit high and puddling fuel.  Then allowing puddled fuel to go down the intake track to cylinder when dropped to ground or raised straight up like I showed you that day.   

Soon see............
REDNECK Saw Repair

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 338 oiler
« Reply #27 on: March 11, 2014, 08:26:58 pm »
What is slimy, green and carries a rifle?































Mucous McCain!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline gunrac

  • 4 cube
  • **
  • Posts: 55
  • Karma: 5
  • Location: Marion Ohio
Re: 338 oiler
« Reply #28 on: March 11, 2014, 09:03:47 pm »
What is slimy, green and carries a rifle?































Mucous McCain!

and his boy, Lark.............lol

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: 338 oiler
« Reply #29 on: March 11, 2014, 09:07:30 pm »
Pa, can I have the 50 steak?
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

 

Related Topics

  Subject / Started by Replies Last post
PP 655 Oiler

Started by blsnelling « 1 2 » Poulan

10 Replies
347 Views
Last post October 18, 2013, 11:20:35 pm
by blsnelling
166 oiler

Started by chadstone « 1 2 3 » Dolmar Makita

21 Replies
742 Views
Last post August 05, 2014, 07:38:22 pm
by Cut4fun
5 Replies
173 Views
Last post December 08, 2013, 05:47:14 pm
by Fish
2 Replies
167 Views
Last post January 10, 2014, 09:45:18 am
by Fish
5 Replies
533 Views
Last post January 19, 2017, 09:55:19 pm
by farmboy
70E oiler

Started by ub54 Jonsered

8 Replies
688 Views
Last post March 01, 2017, 06:54:56 pm
by ub54
0 Replies
201 Views
Last post October 24, 2017, 10:47:26 pm
by rlamppa1
3 Replies
333 Views
Last post February 03, 2018, 09:31:43 pm
by Cut4fun .
5 Replies
265 Views
Last post July 05, 2018, 10:42:25 am
by Cut4fun .
5 Replies
143 Views
Last post July 13, 2020, 07:26:21 pm
by mowertech