« previous next »
Pages: [1] 2   Go Down

Author Topic: old husqvarna chainsaw  (Read 403 times)

0 Members and 0 Guests are viewing this topic.

Offline alex matthew

  • 3 cube
  • *
  • Posts: 11
  • Karma: 0
old husqvarna chainsaw
« on: November 05, 2014, 07:28:17 am »
anyone know how to set up an old tillotson carb for an old husky i.e approx. how many turns high and low please to get me started
Logged

Share on Facebook Share on Twitter

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: old husqvarna chainsaw
« Reply #1 on: November 05, 2014, 08:27:04 am »
I never know how many turns out for I set them up initially at a couple turns - after startup - I adjust the saw to where it runs correctly. Then who knows how many turns out they are?
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna
Re: old husqvarna chainsaw
« Reply #2 on: November 05, 2014, 09:31:06 am »
What model of saw is it? HVA suggests starting 1 turn open from lightly seated for both L & H as a starting point, then tune from there.
Logged
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2108
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: old husqvarna chainsaw
« Reply #3 on: November 05, 2014, 01:07:26 pm »
Yep.  1 and 1 should getcha close enough to start.  Then get the saw warmed up and tune it per my sig line.  Many Husky models used the Tillotson HS.
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: old husqvarna chainsaw
« Reply #4 on: November 05, 2014, 02:50:31 pm »
Yep, one and one for most models - but there are exceptions in the advice from Husky (nothing major though).
Logged

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: old husqvarna chainsaw
« Reply #5 on: November 05, 2014, 04:19:35 pm »
Several small saws use 1-1/2  to 2 turns on the needles.

Not knowing what saw the original poster has, it is best to open the needles greater than one turn.

If too far open, the saw will still start but be too rich. From that point the needles can be adjusted for the chainsaw to run properly.
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: old husqvarna chainsaw
« Reply #6 on: November 06, 2014, 04:24:12 am »
The best is of course to look up the manual for the saw in question ømand leave any guesswork out.  ;)
Logged

Offline alex matthew

  • 3 cube
  • *
  • Posts: 11
  • Karma: 0
old husqvarna chainsaw
« Reply #7 on: November 06, 2014, 07:02:27 am »
thanks to all who replied,that should get me going,i cant pull the starter for too long as I have a very bad shoulder thanks again
Logged

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 68
  • Information collector
  • Location: Troms, North Norway
Re: old husqvarna chainsaw
« Reply #8 on: November 08, 2014, 06:25:22 am »
Quote from: SawTroll on November 06, 2014, 04:24:12 am
The best is of course to look up the manual for the saw in question, and leave any guesswork out.  ;)
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21772
  • Karma: 519
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: old husqvarna chainsaw
« Reply #9 on: November 08, 2014, 09:46:59 am »
Still wondering what chainsaw? Betting 2 1st or 1 2nd series.
Logged
REDNECK Saw Repair Getter Done
Pages: [1] 2   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
7 Replies
1723 Views 		Last post April 20, 2012, 07:22:04 am
by farmboy
11 Replies
616 Views 		Last post December 14, 2012, 12:57:41 pm
by farmboy
33 Replies
3164 Views 		Last post May 21, 2014, 07:49:28 am
by pete
11 Replies
537 Views 		Last post November 01, 2013, 09:19:50 pm
by 660magnum
17 Replies
566 Views 		Last post January 02, 2014, 08:07:26 am
by SawTroll
20 Replies
346 Views 		Last post February 28, 2014, 03:43:56 pm
by SawTroll
14 Replies
506 Views 		Last post July 01, 2014, 05:05:20 pm
by radco
2 Replies
111 Views 		Last post March 09, 2015, 08:52:32 pm
by fuzz1500
0 Replies
162 Views 		Last post April 19, 2017, 01:05:45 pm
by Cut4fun
1 Replies
175 Views 		Last post November 28, 2019, 06:02:46 pm
by Philbert