« previous next »
Pages: [1]   Go Down

Author Topic: Ported 550xp  (Read 915 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4044
  • Karma: 159
  • OHIO REDNECK
Ported 550xp
« on: July 25, 2012, 01:11:48 pm »
So Mitch you were the first to port one so it seems in North America, heck maybe even over the UK guys too.

http://www.youtube.com/watch?v=a8fwFsFUVKI
Logged
REDNECK Saw Repair

Share on Facebook Share on Twitter

Offline mdavlee .

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1968
  • Karma: 171
Re: Ported 550xp
« Reply #1 on: July 25, 2012, 05:35:40 pm »
It looks good. Maybe husky made a 50cc saw with enough power for me. :D
Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4044
  • Karma: 159
  • OHIO REDNECK
Re: Ported 550xp
« Reply #2 on: July 25, 2012, 05:41:41 pm »
Quote from: Gatekeeper on July 25, 2012, 05:35:40 pm
Maybe husky made a 50cc saw with enough power for me. :D

That ported Dan Henry 346xpg 50cc I ran at Ohio gtg with just 346 heated carb felt like a mini 372 in the cut. Andre's 346 50cc with 357 carb felt the same way. Strong.
Logged
REDNECK Saw Repair

Offline mweba

  • Piped Saw
  • *****
  • Posts: 390
  • Karma: 53
Re: Ported 550xp
« Reply #3 on: July 27, 2012, 01:40:26 pm »
I've run a 346 built by Andre, owned by Mike.  It is a solid running saw to be sure. 

Didn't do anything drastic to this one, making improvements that fared well in its big brother.  This new series responds well IMO.

Can't wait to see what Ed comes up with.
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Ported 550xp
« Reply #4 on: July 27, 2012, 01:50:29 pm »
Mitch curious what the ported 550 autotune rpm's sets itself at out of the wood. I set my ported 346's fat around 13.8 for firewood cutting etc.
Logged
REDNECK Saw Repair Getter Done

Offline mweba

  • Piped Saw
  • *****
  • Posts: 390
  • Karma: 53
Re: Ported 550xp
« Reply #5 on: July 27, 2012, 03:43:12 pm »
Quote from: Cut4fun2 on July 27, 2012, 01:50:29 pm
Mitch curious what the ported 550 autotune rpm's sets itself at out of the wood. I set my ported 346's fat around 13.8 for firewood cutting etc.


No idea as the tach goes nutty.  Fastest recorded rpm by the micropr was 14100 though.

Just played with the timing a bit.  Anything at or past 1/3 key will not allow the saw to rev.  Settled on approx 1/4 key.  Will measure that out later. 
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 390
  • Karma: 53
Re: Ported 550xp
« Reply #6 on: July 27, 2012, 10:09:44 pm »
Here is the finished product.

I got stock :10 :10 :09

Finished :07 :07 :06 :07

http://www.youtube.com/watch?v=DWlkG96vbEE
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
20 Replies
1143 Views 		Last post June 29, 2014, 06:00:21 pm
by user10
6 Replies
201 Views 		Last post May 17, 2015, 09:33:57 am
by Cut4fun .
4 Replies
333 Views 		Last post October 15, 2015, 10:43:07 pm
by ch74
2 Replies
494 Views 		Last post March 10, 2016, 02:54:55 pm
by 660magnum
1 Replies
182 Views 		Last post September 23, 2016, 05:27:42 pm
by Cut4fun .
9 Replies
211 Views 		Last post July 13, 2017, 03:46:25 pm
by HolmenTree
2 Replies
262 Views 		Last post February 16, 2018, 10:41:31 pm
by farmboy
1 Replies
85 Views 		Last post January 30, 2018, 08:23:23 am
by HolmenTree
11 Replies
553 Views 		Last post June 08, 2018, 05:08:23 am
by rupe
0 Replies
124 Views 		Last post March 21, 2019, 10:42:16 am
by Cut4fun .