Author Topic: source for seals  (Read 257 times)

0 Members and 0 Guests are viewing this topic.

Online president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
source for seals
« on: January 16, 2014, 08:11:02 pm »
where can I buy a set of crank seals for an old 65l husky
and were they also interchangeable on other models,thanks in advance Keith

Share on Facebook Share on Twitter


Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Online president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: source for seals
« Reply #2 on: January 17, 2014, 12:12:34 am »
thanks Magnum ,dealer said they were NLA Keith

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: source for seals
« Reply #3 on: January 17, 2014, 01:07:29 am »
I'm sorry but I just can not get anywhere finding those
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: source for seals
« Reply #4 on: January 17, 2014, 01:58:54 am »
thanks Magnum ,dealer said they were NLA Keith

Your dealer just doesn't wanna be bothered with somebody fixing an 'old saw'.  That saw uses the same seals as a 272XP...

http://www.ereplacementparts.com/sealing-ring-p-616990.html
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline jockeydeuce

  • 4 cube
  • **
  • Posts: 41
  • Karma: 7
Re: source for seals
« Reply #5 on: January 22, 2014, 08:36:05 pm »
I get nice replacement seals from my local bearing supply....They are 15mm x 26mm x 6mm ....About $2 each


Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: source for seals
« Reply #6 on: January 22, 2014, 08:47:11 pm »
Rob are they double lip with a garter spring?  Do you have the CR/SKF/Timken/National/whatever numbers for those?
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Online president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: source for seals
« Reply #7 on: January 22, 2014, 10:42:34 pm »
 :D thanks, The saw looks mint ,but that vintage and little use is
sure to set some pucker in dem old seals...Keith

Offline jockeydeuce

  • 4 cube
  • **
  • Posts: 41
  • Karma: 7
Re: source for seals
« Reply #8 on: January 22, 2014, 11:23:10 pm »
Rob are they double lip with a garter spring?  Do you have the CR/SKF/Timken/National/whatever numbers for those?

Yes, they are nice double lip seals with the spring.....They come in a generic package with as many as I order in one bag....I buy 8 or 10 at a time for both the 266, etc. & the 288 etc.

I can post a pic tomorrow. Maybe you can decipher a #.....The part # is the size (ID-OD-width)....They are a full nitrile seal with a rubberized outside, if you know what I mean.

 

Related Topics

  Subject / Started by Replies Last post
15 Replies
744 Views
Last post September 24, 2013, 07:23:56 pm
by Cut4fun .
8 Replies
931 Views
Last post November 07, 2016, 05:37:38 pm
by oldpro
18 Replies
504 Views
Last post November 11, 2013, 09:19:48 am
by KilliansRedLeo
43 Replies
972 Views
Last post January 26, 2016, 01:16:30 pm
by Cut4fun .
8 Replies
242 Views
Last post January 26, 2014, 03:18:52 am
by Eccentric
8 Replies
220 Views
Last post March 03, 2014, 05:29:59 pm
by adam32
8 Replies
146 Views
Last post April 27, 2014, 01:11:55 pm
by KilliansRedLeo
7 Replies
150 Views
Last post December 15, 2014, 01:28:20 pm
by 660magnum
4 Replies
387 Views
Last post September 21, 2015, 02:15:01 pm
by jeff.lary
26 Replies
1596 Views
Last post May 16, 2016, 09:03:07 pm
by Cut4fun .