« previous next »
Pages: [1]   Go Down

Author Topic: source for seals  (Read 257 times)

0 Members and 0 Guests are viewing this topic.

Offline president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
source for seals
« on: January 16, 2014, 08:11:02 pm »
where can I buy a set of crank seals for an old 65l husky
and were they also interchangeable on other models,thanks in advance Keith
Logged

Share on Facebook Share on Twitter

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: source for seals
« Reply #1 on: January 16, 2014, 08:49:01 pm »
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: source for seals
« Reply #2 on: January 17, 2014, 12:12:34 am »
thanks Magnum ,dealer said they were NLA Keith
Logged

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: source for seals
« Reply #3 on: January 17, 2014, 01:07:29 am »
I'm sorry but I just can not get anywhere finding those
Logged
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: source for seals
« Reply #4 on: January 17, 2014, 01:58:54 am »
Quote from: president on January 17, 2014, 12:12:34 am
thanks Magnum ,dealer said they were NLA Keith

Your dealer just doesn't wanna be bothered with somebody fixing an 'old saw'.  That saw uses the same seals as a 272XP...

http://www.ereplacementparts.com/sealing-ring-p-616990.html
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline jockeydeuce

  • 4 cube
  • **
  • Posts: 41
  • Karma: 7
Re: source for seals
« Reply #5 on: January 22, 2014, 08:36:05 pm »
I get nice replacement seals from my local bearing supply....They are 15mm x 26mm x 6mm ....About $2 each

Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: source for seals
« Reply #6 on: January 22, 2014, 08:47:11 pm »
Rob are they double lip with a garter spring?  Do you have the CR/SKF/Timken/National/whatever numbers for those?
Logged
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline president

  • 4 cube
  • **
  • Posts: 28
  • Karma: 5
Re: source for seals
« Reply #7 on: January 22, 2014, 10:42:34 pm »
 :D thanks, The saw looks mint ,but that vintage and little use is
sure to set some pucker in dem old seals...Keith
Logged

Offline jockeydeuce

  • 4 cube
  • **
  • Posts: 41
  • Karma: 7
Re: source for seals
« Reply #8 on: January 22, 2014, 11:23:10 pm »
Quote from: Eccentric on January 22, 2014, 08:47:11 pm
Rob are they double lip with a garter spring?  Do you have the CR/SKF/Timken/National/whatever numbers for those?

Yes, they are nice double lip seals with the spring.....They come in a generic package with as many as I order in one bag....I buy 8 or 10 at a time for both the 266, etc. & the 288 etc.

I can post a pic tomorrow. Maybe you can decipher a #.....The part # is the size (ID-OD-width)....They are a full nitrile seal with a rubberized outside, if you know what I mean.
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
15 Replies
744 Views 		Last post September 24, 2013, 07:23:56 pm
by Cut4fun .
8 Replies
931 Views 		Last post November 07, 2016, 05:37:38 pm
by oldpro
18 Replies
504 Views 		Last post November 11, 2013, 09:19:48 am
by KilliansRedLeo
43 Replies
972 Views 		Last post January 26, 2016, 01:16:30 pm
by Cut4fun .
8 Replies
242 Views 		Last post January 26, 2014, 03:18:52 am
by Eccentric
8 Replies
220 Views 		Last post March 03, 2014, 05:29:59 pm
by adam32
8 Replies
146 Views 		Last post April 27, 2014, 01:11:55 pm
by KilliansRedLeo
7 Replies
150 Views 		Last post December 15, 2014, 01:28:20 pm
by 660magnum
4 Replies
387 Views 		Last post September 21, 2015, 02:15:01 pm
by jeff.lary
26 Replies
1597 Views 		Last post May 16, 2016, 09:03:07 pm
by Cut4fun .