Author Topic: Tuning a saw  (Read 2322 times)

0 Members and 54 Guests are viewing this topic.

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: Tuning a saw
« Reply #20 on: April 13, 2011, 11:04:29 am »
Another little tip is to "read " the plug .Properly tuned it should have a slight brownish tint to it .Too rich is black and too lean will be whiteish .It's always better to err on the side of caution and be too rich as too lean .

Pretty simple .Clean the plug, run the saw hard for 10 15 minutes .Let it cool off and check it .

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4666
  • Karma: 216
  • OHIO REDNECK

  • Total Badges: 44
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 7 Seventh year Anniversary Apple User
Re: Tuning a saw
« Reply #21 on: April 13, 2011, 01:21:02 pm »

Offline 05_sprcrw

  • 4 cube
  • **
  • Posts: 65
  • Karma: 3

  • Total Badges: 17
    Badges: (View All)
    Level 4 Third year Anniversary Search Mobile User Windows User Karma Good
Re: Tuning a saw
« Reply #22 on: April 14, 2011, 07:58:27 am »
I do know how to read a plug (assuming its similar to a regular vehicle spark plug).  Thanks for all the tips this is the first time I have really done a complete tune myself instead of just minor adjustments and appreciate all the help I have received.

Offline HolmenTree

  • Nitro Hotsaw
  • *******
  • Posts: 1382
  • Karma: 199
  • Location: Manitoba Canada

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 1000 Posts Seventh year Anniversary
Re: Tuning a saw
« Reply #23 on: April 14, 2011, 11:57:57 am »
Most times reading a plug does not prevent damage because when you figure out the problem with the color the damage is already done.
Another good advice is when reving a saw to WOT out of the cut, is don't blip the throttle up and down to WOT quickly. Its OK to blip the throttle to WOT quickly, but let off the throttle trigger "slowly" back to idle. This saves alot of stress on the connecting rod bearings.

Willard. 
Making a living with a saw since age 16.

Offline 05_sprcrw

  • 4 cube
  • **
  • Posts: 65
  • Karma: 3

  • Total Badges: 17
    Badges: (View All)
    Level 4 Third year Anniversary Search Mobile User Windows User Karma Good
Re: Tuning a saw
« Reply #24 on: April 18, 2011, 07:24:58 am »
Thanks I did not know that, I have used saws for a long time just never took the time to learn the internal workings or complete tare downs until now.  Forums like this sure make it seem a whole lot less daunting.

Offline 05_sprcrw

  • 4 cube
  • **
  • Posts: 65
  • Karma: 3

  • Total Badges: 17
    Badges: (View All)
    Level 4 Third year Anniversary Search Mobile User Windows User Karma Good
Re: Tuning a saw
« Reply #25 on: May 04, 2011, 12:45:06 pm »
Just wanted to let everyone know I got a good grasp of things now and have the saw tuned nicely and hope to do some cutting with it this weekend.

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
2223 Views
Last post August 22, 2012, 07:06:45 pm
by AussieRedGum
28 Replies
2930 Views
Last post November 09, 2013, 03:04:59 pm
by Cut4fun .
5 Replies
506 Views
Last post February 07, 2014, 06:05:21 pm
by KilliansRedLeo
11 Replies
674 Views
Last post February 28, 2014, 03:14:46 pm
by Cut4fun
15 Replies
839 Views
Last post April 04, 2014, 11:17:57 pm
by Reddog
23 Replies
969 Views
Last post April 17, 2014, 04:37:58 am
by KilliansRedLeo
7 Replies
560 Views
Last post April 21, 2014, 09:42:26 pm
by rms61moparman
3 Replies
382 Views
Last post August 02, 2014, 06:57:23 pm
by Cut4fun .
4 Replies
517 Views
Last post September 18, 2014, 01:47:38 pm
by pigpen60
1 Replies
723 Views
Last post December 11, 2014, 01:29:35 pm
by 660magnum