Chainsaw Repair

Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Husqvarna => Topic started by: Randy on February 10, 2014, 09:32:15 pm

Title: 345 leaking oil
Post by: Randy on February 10, 2014, 09:32:15 pm
First time on the site. My problem is that my 345 Husky sweats oil out of the oil passage to the bar. I'm fairly mechanically inclined. I would like to know  where I could get a repair manual or at least a link to for this repair. I fixed a lot of saws, but never repaired an oiler problem. I'm not even sure how these oilers are supposed to operate.
Thanks, Randy
Title: Re: 345 leaking oil
Post by: 660magnum on February 11, 2014, 01:37:50 am
Look in your Gmail for a 345 Service Manual
Title: Re: 345 leaking oil
Post by: Randy on February 11, 2014, 11:22:34 am
660, Thank you for the manual. Will be working on it today. What a help.
Randy
Title: Re: 345 leaking oil
Post by: KilliansRedLeo on February 11, 2014, 11:41:22 am
I have had a lot of people tell me that they have had the same problem in 345s, 346 both OE & NE editions. Is this something characteristic of these saws? Some sort of design issue or a systemic malady of sorts? Is there some sort of generic fix that usually cures the problem?
Title: Re: 345 leaking oil
Post by: Randy on February 11, 2014, 12:44:10 pm
Ok-I got the pump and filter out of the saw. Everything "looks" ok, however not sure what to do next. I do have the saw pretty much stripped down due to changing fuel line. I'm just thinking getting all new parts. Thanks Killianredleo for some reassurance that I don't have a rare problem. Randy
Title: Re: 345 leaking oil
Post by: 660magnum on February 11, 2014, 01:42:01 pm
Get all new rubber and plastic parts for the pump assembly
Title: Re: 345 leaking oil
Post by: Randy on February 12, 2014, 09:56:07 am
Thanks for the suggestion. All new parts are ordered and I will post the results.
Title: Re: 345 leaking oil
Post by: Randy on February 20, 2014, 10:02:42 pm
Parts came in and installed. Ran the saw for a short time just to make sure the pump worked. Pump works good and the saw sat for the afternoon and "no" leak. So far so good. I would recommend replacing all the parts.

Thanks for all the advice. Great forum!
Randy
Title: Re: 345 leaking oil
Post by: 660magnum on February 21, 2014, 12:27:09 am
+1
Title: Re: 345 leaking oil
Post by: KilliansRedLeo on February 21, 2014, 11:30:14 am
As 660 said new rubber parts. I noticed that my own 346NE was drooling oil all over the place the other day. Took it apart, everything looked Kosher. However when I touched the oil delivery line to the bar it fell off the pump output. I removed the pump and the oil supply line. Cleaned them up and then tried to put them in place on the 346 metal oil pump. They would not stay where they were supposed to go, they would just fall off. Looking some more I noticed that they may be intended to be a press fit around the pump. So ordered new lines and when they arrived tried the same process with them, they fit tight to the pulp input and output. When installed in the saw the supply line goes first, then the pump then the output to the bar and it appears that all of this is held in place with the bar plate.

The pick up and delivery lines are #15 & 16 in the attach clip from the IPL, you can see how they wrap around the pump and fit onto the small inlet and outpup barbs on the pump. It looks as though there is a flange on the oil supply line that would seal the tank but the line I received did not have a flange.

I inspected the bar plate for damage and compared it to a new one, looked good. When I was installing the bar plate I could feel it compressing the rubber hoses around the pump body. Been sitting for a while now and no more drool.
Title: Re: 345 leaking oil
Post by: 660magnum on February 21, 2014, 11:56:08 am
Plastic item #12 doesn't last very long. While you are in there you may as well replace it too.