Chainsaw Repair

Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Poulan => Topic started by: Cut4fun on December 03, 2014, 12:50:15 pm

Title: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun on December 03, 2014, 12:50:15 pm
Saving a post Aaron made.    I'll check on the 3000-365-3750 seals but pretty sure they all got thrown in the trash when removed.

Eccentric

I'm having zero luck finding the 8500 clutch parts I need. They're now NLA. A TON of Poulan parts (for the 4200-8500 series, the XXV series, the 3400-4000 series, and even the relatively recent 3450/3750/PP330/PP380 series have been going NLA over the last few months. Same with many of the Husqvarna 200-series saw parts. Looks like HVA/Poulan is 'cleaning house'.....

Looks like I'll have to make the parts I need. For the three clutch washers........I can most likely drill 4200/5200 parts that I have (from parts saws) for the larger crank snout diameter. I'm SOL on the clutch bearing inner race however (because the ID and OD are larger than the 4200-5400 parts).

Would somebody who has a 6900/7700/8500 please measure your saws inner race for me so I can replicate it? May be able to luck out and find a match from some other saw. At the least, I can have somebody machine a race from tubing. I mostly need the OD and length measurements. Can figure out ID from the crank snout diameter. Thanks in advance.......

On the subject of recently NLA parts, it'd be helpful for many if we can figure out an industry equivalent for the 2700-3600/3450-3750/PP330-380/PP365/etc saw crank seals. They're "back ordered" from Poulan, with no expected date of availability (same for the both the smaller and larger intake boots BTW).

I only have one of those saws here right now (belongs to somebody else), and I'm not going to pull those seals to make accurate measurements of the housing bores, shaft diameters, and such needed to find a match unless I have a set of replacement seals in hand to replace them with. Would somebody please make those measurements so we can find industry matches? That would help many folks in the future.

Aside from the 'clamshell' Poulans, just about all the crank seals for Poulan saws are now NLA. Thankfully, folks have found industry equivalents for most of them. We've gotta do the same thing with that last "pro" Poulan series.....

Here are some seal #'s that have already been found by various folks:

-Poulan Micro series 530019059. Back ordered from Poulan, with no ETA. These JUST went back-ordered. They were in stock as of last month. IF you can get them from your dealer/parts source (my Husky dealer had 4 in stock last year....I grabbed them all), they're till cheapest to get these right from your Husky/Poulan parts source. IF that's not an option, then.........you can use SKF 4913.

-Poulan XXV Series:

Both sides 530019051. Back ordered last spring. Just checked again and there are a few available. I'll be grabbing those shortly.... SKF/CR 5510 is a match, as is National/Timken 313156.

-Poulan 3400-4000 and PP375-395 Series:

Both sides 530019097. NLA. SKF 6119. National/Timken 253747.

-Poulan 4200-8500 Series:

Both sides 530019075. Back ordered with no ETA. SKF 6904. National 471466.

Poulan 306/245:

FW side 530019042. Back ordered with no ETA. CR 5542 or 5541.

PTO Side 530001936. NLA. Dichtomatik 068091VM (dist by Rankin Industries).

Oil Pump body seal 530019035. Back ordered with no ETA. Dichtomatik 06081SM.
Title: Re: poulan parts NLA
Post by: Eccentric on December 04, 2014, 12:28:04 am
Hey that looks familiar....8)


It's getting BAD.  I've been looking more Poulan parts up on Ordertree.  MANY parts that were still available are now NLA, or back ordered with no date of availability.  Grim....


Kevin do you have any 2800-3600/3450-3750/etc cranks and cases to measure?  Case bore diameter, case depth, and shaft diameter are what we need to find matching seals.

For this saw series, 530019146 is the Poulan #.

http://www.ereplacementparts.com/crankshaft-seal-p-247914.html
Title: Re: poulan parts NLA
Post by: Tractorsaw1 on December 04, 2014, 07:36:22 am
I noticed the same last night.  I know just a few months ago I had looked for a top cover for a 505 & seen I could get it, looked last night nla.
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 04, 2014, 08:32:30 pm
None apart to measure.   Hoping I threw a old seal in a bin.
Title: Re: poulan parts NLA
Post by: 3000 FPS on December 04, 2014, 09:33:02 pm
Aaron I have a brand new set of seals for that series of saws.   They are in town and if you can wait I will pick them up and research out a generic replacement for them.   I am going into town on Saturday and will get them then.  I also have about 10 saws that use those seals and can measure one of them also.
Title: Re: poulan parts NLA
Post by: Eccentric on December 05, 2014, 01:30:35 pm
Aaron I have a brand new set of seals for that series of saws.   They are in town and if you can wait I will pick them up and research out a generic replacement for them.   I am going into town on Saturday and will get them then.  I also have about 10 saws that use those seals and can measure one of them also.


Thank you Roger!
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 05, 2014, 08:37:20 pm
Found 4 new 530019146 seals. Paid through the nose for them though  :o.  $32 to my door shipping and tax.  But at least I got some now.
Title: Re: poulan parts NLA
Post by: 3000 FPS on December 05, 2014, 09:13:55 pm
Found 4 new 530019146 seals. Paid through the nose for them though  :o.  $32 to my door shipping and tax.  But at least I got some now.

Good for you.  It is just a matter of time those seals will get used.   They were used on a lot of different models.   
I would say Poulan understood the meaning of standardization.
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 06, 2014, 11:56:22 am
Found 4 new 530019146 seals. Paid through the nose for them though  :o.  $32 to my door shipping and tax.  But at least I got some now.

Good for you.  It is just a matter of time those seals will get used.   They were used on a lot of different models.   
I would say Poulan understood the meaning of standardization.

Thats why I had to have them. Have 2900 3.0 3500 365 3450 on hand of the top of my head  and some  project stage ones.  Plus dads 3300 he bought new and friends own my old 3750 335 etc. So having parts on hand is nice if they are going to go NLA on us.  :'(

I tried to order 10 and said no go, then 9 8 7 6 5 all with no go  :-X.  Put in 4 and bingo order took. Felt like a kid in a candy store.
Title: Re: poulan parts NLA
Post by: Eccentric on December 06, 2014, 04:24:33 pm
Found 4 new 530019146 seals. Paid through the nose for them though  :o.  $32 to my door shipping and tax.  But at least I got some now.

Good for you.  It is just a matter of time those seals will get used.   They were used on a lot of different models.   
I would say Poulan understood the meaning of standardization.

Thats why I had to have them. Have 2900 3.0 3500 365 3450 on hand of the top of my head  and some  project stage ones.  Plus dads 3300 he bought new and friends own my old 3750 335 etc. So having parts on hand is nice if they are going to go NLA on us.  :'(

I tried to order 10 and said no go, then 9 8 7 6 5 all with no go  :-X.  Put in 4 and bingo order took. Felt like a kid in a candy store.

Was it ordertree?  Last week when I tried they didn't have any available.  Entered 10 and it showed that 10 would be backordered.  Don't need 10....................but that's what I do to see how many they actually have in stock.  MANY Poulan and Husky parts come up in a search....................but show zero being available when I try adding them to my cart......

PLEASE measure those seals when ya get 'em.  If anybody has some cases and cranks to measure we'd appreciate those measurements too. 
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 06, 2014, 06:14:07 pm
Found 4 new 530019146 seals. Paid through the nose for them though  :o.  $32 to my door shipping and tax.  But at least I got some now.

Good for you.  It is just a matter of time those seals will get used.   They were used on a lot of different models.   
I would say Poulan understood the meaning of standardization.

Thats why I had to have them. Have 2900 3.0 3500 365 3450 on hand of the top of my head  and some  project stage ones.  Plus dads 3300 he bought new and friends own my old 3750 335 etc. So having parts on hand is nice if they are going to go NLA on us.  :'(

I tried to order 10 and said no go, then 9 8 7 6 5 all with no go  :-X.  Put in 4 and bingo order took. Felt like a kid in a candy store.

Was it ordertree?  Last week when I tried they didn't have any available.  Entered 10 and it showed that 10 would be backordered.  Don't need 10....................but that's what I do to see how many they actually have in stock.  MANY Poulan and Husky parts come up in a search....................but show zero being available when I try adding them to my cart......

PLEASE measure those seals when ya get 'em.  If anybody has some cases and cranks to measure we'd appreciate those measurements too. 

No. Here in Ohio as to why I had to pay tax too.
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 06, 2014, 06:16:38 pm
Aaron I have a brand new set of seals for that series of saws.   They are in town and if you can wait I will pick them up and research out a generic replacement for them.   I am going into town on Saturday and will get them then.  I also have about 10 saws that use those seals and can measure one of them also.

Have you had a chance to measure?  See how close I come to yours in my measuring with my cheap calibers.
Title: Re: poulan parts NLA
Post by: Sty57 on December 06, 2014, 08:34:43 pm
Does anyone know of a available piston for the 5200?
Or is there anything that is close that can be used with some machine work?
Title: Re: poulan parts NLA
Post by: Eccentric on December 06, 2014, 10:02:42 pm
Does anyone know of a available piston for the 5200?
Or is there anything that is close that can be used with some machine work?

They are not available, except for the odd leftover NOS piston that shows up every now and then.  AFAIK, there's nothing that's a ready substitute.  If you find a substitute, PLEASE let me know.....
Title: Re: poulan parts NLA
Post by: Sty57 on December 07, 2014, 06:54:32 am
Does anyone know of a available piston for the 5200?
Or is there anything that is close that can be used with some machine work?

They are not available, except for the odd leftover NOS piston that shows up every now and then.  AFAIK, there's nothing that's a ready substitute.  If you find a substitute, PLEASE let me know.....
Will do
Title: Re: poulan parts NLA
Post by: 3000 FPS on December 07, 2014, 01:26:20 pm
Ok I got my seals for the 3750 and my dial calipers.  The seal it self only had the part number on it and no other reference.

I measured the outside diameter of the seal it self.   It is 35mm
I then measured the crankshaft for Inside diameter.  It is 14.25mm
I then measured the thickness of the seal which is important because the oil pump has to sit
over it.   It is 4.8mm

   I then  made the same measurements with my other calipers that give thousanths.
    OD.   1.380"
    ID.    .562"
wide.     .190"

So let the games begin the first to find a replacement wins everyones appreciation.   Thanks guys I do not have time right now to research it but will start tonight when I get home.
Title: Re: poulan parts NLA
Post by: 3000 FPS on December 07, 2014, 01:29:58 pm
I forgot to add that they are a single lip seal with a spring tension.
Title: Re: poulan parts NLA
Post by: Cut4fun . on December 07, 2014, 02:51:11 pm
Thanks Roger. Mine are still in the mail I hope.
Title: Re: poulan parts NLA
Post by: Eccentric on December 07, 2014, 11:01:31 pm
Thanks Roger!  Now to cross-ref...
Title: Re: poulan parts NLA
Post by: Eccentric on December 07, 2014, 11:52:28 pm
http://www.masterseals.com.sg/SKF%20Shaft%20Seals.pdf

http://www2.chicago-rawhide.com/

http://www.timken.com/en-us/products/Documents/Seal-Specification-Guide.pdf


Did some searching.  May have found a match in the Timken catalog.  471551.   Construction and measurements appear to be compatible...........except it is a bit wider than the OEM seal (.252" vs .190").  Don't know if that's a deal breaker or not.  Did not find a Metric match.  From the Timken catalog:

Timken 471551

Style:       470 (double lip w spring) 

Material:   S (Nitrile rubber) 

Shaft dia:  0.563"

Bore dia:   1.378"

Seal OD:    1.384"

Seal width:0.252"



Put that Timken # into the handy-dandy CR/SKF seal interchange thingee...............and found an SKF match.  SKF 5756.

http://www2.chicago-rawhide.com/popup_parts_lookup_457012.htm


http://www.skfextranet.com/Catalogs/457010/sealdetail.asp?s=5756

Looks to be a Nitrile rubber, single lip (with spring) seal with roughly the same measurements as the Timken seal.

SKF 5756

Shaft- 0.563"

Bore-  1.375"

OD-    1.379"

Width- 0.25"
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 08, 2014, 12:25:12 am
About all you can do is order one and see if it will seat deep enough for the oil pump and worm gear to clear.   It does look close. 
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 08, 2014, 12:33:16 am
Ok I bought one and when I get it I will install it on the PTO side on a 3500 I have here.   Then we will see if it clears the oil pump.   I ordered the SKF 5756.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 08, 2014, 01:00:54 am
Thanks for doing that for us Roger.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 08, 2014, 08:42:39 am
Nice work.   

(http://revmikewilliams.org/thumbs-up-emoticon-facebook-23.jpg)
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 12, 2014, 04:47:21 pm
Thanks Roger. Mine are still in the mail I hope.

Received yesterday 4 seals.  Just been to busy to get on right now.  work work training work.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 13, 2014, 06:17:18 pm
I got the new seal in and pulled the old one out of the 3500.
There is not going to work because I measured the shaft size wrong. 
There was another step in the shaft I did not see until I got the worm gear off.
I believe I could have made this seal work if it was not for the shaft size being wrong.

The size should be as follows.
Diameter 1.380
Width.      .190 but I measured the case and a seal as wide as .220 would work.
Shaft.       .590

The seal I pulled out of the 3500 also had a number on it.
NOK  UDO 421E
MADE IN SINGAPORE.
Sorry if you come up with another that might work let me know and I will give it a go.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 13, 2014, 06:34:22 pm

The seal I pulled out of the 3500 also had a number on it.
NOK  UDO 421E
MADE IN SINGAPORE.


The new ones I got in have no markings or lettering numbers etc.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: farmboy on December 13, 2014, 07:07:31 pm
The two I have don't have any marking either.
Shep
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 14, 2014, 12:24:19 am
I got the new seal in and pulled the old one out of the 3500.
There is not going to work because I measured the shaft size wrong. 
There was another step in the shaft I did not see until I got the worm gear off.
I believe I could have made this seal work if it was not for the shaft size being wrong.

The size should be as follows.
Diameter 1.380
Width.      .190 but I measured the case and a seal as wide as .220 would work.
Shaft.       .590

The seal I pulled out of the 3500 also had a number on it.
NOK  UDO 421E
MADE IN SINGAPORE.
Sorry if you come up with another that might work let me know and I will give it a go.

Searched the Timken catalog again.  Found a seal that matches the bore and shaft diameters, but it's too wide at .276"

Did some maths and figured out that the new correct shaft diameter is right about 15mm.  Off to the metric charts to find a match.  Need to find one with a 35mm OD, 15mm shaft diameter, and 4.8mm width.  BRB...
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 14, 2014, 12:31:22 am
Nothing yet.  Found a metric that matches the shaft and bore diameters..............but it's probably too wide at 7mm.  If my maths be right, the max with (.220") is around 5.588mm.  Will search more later.  The baby sez it's time for me to be done on the computer for a spell....
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 14, 2014, 12:52:20 am
Aaron if you cannot find anything else then give me the number for the one that is too wide at .276.
There is a chance that part of the metal for the width can be ground off a little to make it fit.  Install it with a little Yamabond and it should work.

7mm = .275. So the 7mm width is about the same as the other one you found.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 14, 2014, 01:45:27 am
Aaron if you cannot find anything else then give me the number for the one that is too wide at .276.
There is a chance that part of the metal for the width can be ground off a little to make it fit.  Install it with a little Yamabond and it should work.

7mm = .275. So the 7mm width is about the same as the other one you found.

Hiya Roger,

Here's a quick search I did on feebay for "15mm 35mm oil seal".  Most that came up were too wide, but there was one listing for a 6mm wide double lip seal as well as a listing for a 5mm wide single lip.  5mm is within your allowable measurement of .220".

http://www.ebay.com/sch/i.html?_from=R40&_trksid=p2060778.m570.l1313.TR0.TRC0.H0.X15mm+35mm+oil+seal&_nkw=15mm+35mm+oil+seal&_sacat=0

http://www.ebay.com/itm/Metric-Oil-Shaft-Seal-15-x-35-x-5-15x35x5-15mm-x-35mm-x-5mm-Single-Lip-/161113962093?pt=LH_DefaultDomain_0&hash=item258323f66d

http://www.ebay.com/itm/Metric-Oil-Shaft-Seal-15-x-35-x-6-15x35x6-15mm-x-35mm-x-6mm-Double-Lip-/151127519591?pt=LH_DefaultDomain_0&hash=item232fe6f167


The Timken # for the SAE measurement seal (single lip) that was too wide is 153507XX.  Just noticed that it's notated as a metric seal (in the SAE seal list)........................and is in fact the same part number as the metric seal that I'd also found (in another list).

Now................................both the Ebay seals and the Timken seal that I found are the type with the rubber extending over the seal body.  don't know for sure whether or not those can be trimmed without issue (if needed).  I haven't used this type of seal in a saw before.  Others have without problems however.

I did also find a Timken 471558 seal.  It is an SAE seal that matches our shaft and bore measurements.  It is .312" wide, but is a 'regular' metal bodied single lip seal that could be trimmed.


Still have to check the CR/SKF and Dichtomec (sp?) lists for these measurements.  Gotta let my brain and eyeballs cool a bit before going through more charts however....
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 14, 2014, 01:48:54 am
OK checked one more thing before calling it a night.  Checked the Timken 471558 number in the SKF cross-ref thingee.  Came up with 5966.  It's  a metal bodied, .313" wide double lip nitrile seal.  Hmmm.....

http://www.skfextranet.com/Catalogs/457010/sealdetail.asp?s=5966

http://www2.chicago-rawhide.com/popup_parts_lookup_457012.htm
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 14, 2014, 05:53:23 pm
Good work Aaron.

Ok I have ordered the SKF 5966 and the metric all rubber seal.   When I get them
I will check them both out and let you guys knows the results.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 14, 2014, 05:56:09 pm
Good work Aaron.

Ok I have ordered the SKF 5966 and the metric all rubber seal.   When I get them
I will check them both out and let you guys knows the results.

Sweet.  Thanks for doing that Roger.  Teamwork will conquer this one sooner or later.8)
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 14, 2014, 06:01:06 pm
Good work Aaron.

Ok I have ordered the SKF 5966 and the metric all rubber seal.   When I get them
I will check them both out and let you guys knows the results.

Sweet.  Thanks for doing that Roger.  Teamwork will conquer this one sooner or later.8)


+1
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 14, 2014, 08:59:24 pm
Nice wtg crunching out seals.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 08:10:10 pm
I received the seals today and I am going to install tomorrow.   The rubber coated all metric seal looks very promising.   I was holding it next to the original and it looks like a match to me.    The rubber coating should also provide a good sealing surface also.   I will take some pics tomorrow and let you guys know.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun on December 23, 2014, 08:26:08 pm
Nice. Pics please for sure.

Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 660magnum on December 23, 2014, 09:23:07 pm
Don't overlook the double lip - single lip seal differences and applications.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 09:30:57 pm
Don't overlook the double lip - single lip seal differences and applications.

The one I took out is single lip with a spring and the one I just received is single lip with a spring.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 23, 2014, 09:39:42 pm
Do you need a pic of my oem ones I just received with no numbers etc on them?
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 09:42:51 pm
Do you need a pic of my oem ones I just received with no numbers etc on them?

I have brand new oem seals here Kevin.   They are single lip and a spring.   
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 23, 2014, 09:46:07 pm
Do you need a pic of my oem ones I just received with no numbers etc on them?

I have brand new oem seals here Kevin.   They are single lip and a spring.   

Yep.
I was just wondering why the ones removed had numbers etc. I never noticed it on the ones I have removed. But of course I wasnt paying attention for that either.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 10:07:04 pm
The oem ones that I have actually have the Poulan part numbers on the rubber portion of the seal.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 23, 2014, 10:13:00 pm
I need to look closer then. Without the bifocals to get in real close.   :D ;D ::)  WA-PITA  working on stuff sometimes. In between  :-X.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 10:25:07 pm
I use my 8 power magnifiers to see those numbers.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 23, 2014, 10:38:27 pm
I use my 8 power magnifiers to see those numbers.

I should have done that back when square filing. But I fought it off.  Ones with light and all.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 23, 2014, 10:44:50 pm
I use my 8 power magnifiers to see those numbers.

I should have done that back when square filing. But I fought it off.  Ones with light and all.

I use those magnifiers when using my chain grinders.   I like seeing what is going on with the cutter and get a good view of the results.   I am used to them because of all the watch repair I did for many years.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 23, 2014, 10:49:08 pm
No way I could see inside a watch. Heck I have troubles with the tiny screws replacing a battery nowdays.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 24, 2014, 03:15:37 pm
Ok here we go.   
The first picture is of the all rubber metric seal.   I think it is a winner and I was going to air leak check the crank case but do not have my block off plates here.

Second picture is the all rubber metric seal installed.   I lubed it up real good with some 2 cycle oil and it went in easy peasy.

The third picture is the SKF 5966 seal.   You can see how much wider it is.

The fourth picture is the SKF 5966 after I cut it down to fit.    I could have taken off a little less in the width and I think it still would have worked, but still plan on installing this on the flywheel side. 
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun on December 24, 2014, 04:14:26 pm
How did you cut the bigger seal down?  Also let us know if the rubber one passes the leak test.   Good info.

Can you show me a pic of the inside part of the rubber seal, part facing in toward crankcase?

Thanks for all you guys do finding this stuff.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 12:01:14 am
I do not have a pic of the inside of that seal before I installed it.
The other seal I cut with my foredom flex shaft and a small cut off wheel.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 25, 2014, 04:14:18 am
Great work Roger.  The 380 I'm working on has an air leak, so I'll be picking up seals for it soon.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on December 25, 2014, 04:17:34 am
Also.......are you guys using the 530031115 oil pump drive worm puller?  I need to remember to order one of those too.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 09:11:26 am
Also.......are you guys using the 530031115 oil pump drive worm puller?  I need to remember to order one of those too.

Yes bottom right in pic.   It also works on some jonsered 490 gears and other saws.  490 there was 2 different gears used. Coarse and fine.

(http://i59.photobucket.com/albums/g289/doemaster789/PP505PP365JD800/pp365anflowers007.jpg)
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 09:13:30 am
Which  part number used was the rubber one?   

(http://chainsawrepair.createaforum.com/index.php?action=dlattach;topic=4377.0;attach=10634;image)
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 09:49:19 am
Yes Aaron I used the gear puller like the one Kevin is showing.

Kevin there was no part number when I got it.  I just put 15x35x5 on eBay and it came up $3.14 plus the shipping.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 09:50:55 am
was it this one single lip?

http://www.ebay.com/itm/Metric-Oil-Shaft-Seal-15-x-35-x-5-15x35x5-15mm-x-35mm-x-5mm-Single-Lip-/161113962093?pt=LH_DefaultDomain_0&hash=item258323f66d&rmvSB=true

(https://store-uqohp.mybigcommerce.com/product_images/uploaded_images/a.png)

Single Lip - Rubber Coated w/ Spring

DIN: 3760 Standard
Other Known Types: SC, A, BA, WA, DG, CB, HMS4, Type 35, Model 92, 827N
Materials: Nitrile (NBR)
Spring Make: Standard Carbon Steel

Pressure Rating: Max 7psi
Temp Range: -40 deg F to +248 deg F

Mounting: Press-fit
Comments: Rubber covered O.D. improves sealing ability at the housing, and is kind to softer materials.This style will hold up in low-pressure applications.

Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 09:52:44 am
What do they consider low pressure?  Wonder what a chainsaw crankcase pressure is running wot cutting?

Mounting: Press-fit
Comments: Rubber covered O.D. improves sealing ability at the housing, and is kind to softer materials.This style will hold up in low-pressure applications.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 10:15:43 am
Yep that is the one I put in.    We will see how it holds up, but I would not consider the crank case pressure to be high.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 10:28:24 am
Yep that is the one I put in.    We will see how it holds up, but I would not consider the crank case pressure to be high.

Sounds like same seal but half the total price shipping etc?  http://www.ebay.com/itm/Oil-Shaft-Seal-15-x-35-x-5mm-Price-for-1-pc-/201247726172?pt=LH_DefaultDomain_0&hash=item2edb4c9a5c
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 10:43:48 am
It sure does.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 11:01:41 am
Good info on the rubber coated seal use here.  http://www.ultimateindustrial.com/metric-oil-shaft-seal-15-x-35-x-5-15x35x5-15mm-x-35mm-x-5mm-single-lip/
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 01:35:58 pm
I am surprised that the pressure rating is only 7 PSI.   
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on December 25, 2014, 01:43:51 pm
I am surprised that the pressure rating is only 7 PSI.   

Thats why I am wondering about crankcase pressure running and cutting. Dont people test with mini vac to 10?
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 25, 2014, 09:47:44 pm
I am surprised that the pressure rating is only 7 PSI.   

Thats why I am wondering about crankcase pressure running and cutting. Dont people test with mini vac to 10?

Yep.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 660magnum on December 26, 2014, 01:20:31 am
The test pressure is 1/2 atmosphere

Which is 7 lbs pressure soap bubbles for leaks

or

15" vacuum to double check seals 15" intial vacuum - wait 30 sec and there should be 10" vacuum left or the seals are bad.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on December 26, 2014, 06:36:04 pm
I was going to check the squish on my 3500 before I take the cylinder off and I cannot find my solder.   I will be so glad when everything is organized again and put back where it belongs.   
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 16, 2015, 01:38:02 pm
SOG  Another one gone 415 425 445 475 505 base gasket. Here I was telling dude to just order one for $3-$4.  Amazing how they just drop them in a few months time.

 HOP-503428601

* This product is not available in the requested quantity. 1 of the items will be backordered.
   $3.58
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on January 16, 2015, 03:01:44 pm
HOP/HVA is really cleaning house.  MANY 2-series (288, 272, etc) Husky and 1980's/1990's Poulan/PoulanPro parts are getting the ax.  Not good...
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 16, 2015, 03:20:22 pm
I know they got  me rethinking my future plans of what saws I am going to hold on to.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on January 16, 2015, 05:06:54 pm
Means a lot more improvising.   
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: farmboy on January 17, 2015, 10:12:08 am
Guy has the AF's back on Ebay if your in need.  http://www.ebay.com/itm/Poulan-Air-Filter-Part-530010892-NOS-NLA-/331451330505?pt=LH_DefaultDomain_0&hash=item4d2c09efc9
Shep
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 660magnum on January 17, 2015, 10:15:29 am
He has the 855 suffix filter too
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 17, 2015, 10:17:57 am
Guy has the AF's back on Ebay if your in need.  http://www.ebay.com/itm/Poulan-Air-Filter-Part-530010892-NOS-NLA-/331451330505?pt=LH_DefaultDomain_0&hash=item4d2c09efc9
Shep

Thank you so much for the update. I forgot about the last ones and missed out.  Done deal this time. Thanks.................

Oh I had to pay OH tax but no big deal.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 17, 2015, 10:19:41 am
He has the 855 suffix filter too

mesh http://www.ebay.com/itm/Poulan-Air-Filter-Part-530010855-NOS-NLA-/331451331280
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on January 17, 2015, 11:02:32 am
Pretty good price on those also.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 21, 2015, 06:28:59 pm
Just bought a NOS HDA 137 and NOS small poulan intake. 

So NOS seals, air filters, intake, carb should keep a few going for awhile now.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on January 21, 2015, 08:36:54 pm
Just bought a NOS HDA 137 and NOS small poulan intake. 

So NOS seals, air filters, intake, carb should keep a few going for awhile now.

Good deal on that carb and intake.    Now that these items are NLA they will just get harder to come by.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Eccentric on January 22, 2015, 04:02:09 am
Just bought a NOS HDA 137 and NOS small poulan intake. 

So NOS seals, air filters, intake, carb should keep a few going for awhile now.

Where'd you find those NOS parts Kevin?
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: countryhog on January 22, 2015, 08:45:23 am
roger, wondering if you've had a chance to run the saw with the rubber coated seal?
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: 3000 FPS on January 22, 2015, 11:10:13 am
No I have not.  I am still working on it and have the cylinder off of it right now so I could open the ports a little and I dropped the cylinder by .010".  I do not think I am going to use that seal, I have another one that I cut down and I am going to use it instead.
Title: Re: 2700-3600/3450-3750/PP330-380/etc Crank Seals. Other NLA Poulan Parts
Post by: Cut4fun . on January 22, 2015, 12:23:39 pm
Just bought a NOS HDA 137 and NOS small poulan intake. 

So NOS seals, air filters, intake, carb should keep a few going for awhile now.

Where'd you find those NOS parts Kevin?

I wasnt even looking for them  :P. I was searching for something else. Seen pic of a intake and it looked like the small or big in my mind.
Ran the numbers came back small. So I typed poulan in guys EBAY sells and found the carb too.  I thought why not. Guy appears to buy old stock from somewhere and then list them on ebay. 
Title: Re: NLA Poulan Parts 2700-3600/3450-3750/PP330-380/etc Crank Seals.
Post by: Cut4fun . on February 02, 2015, 11:36:37 am
I hear from a very good source that some NLA poulan parts will soon be able to be bought new aftermarket.   1 of those will be the small intake boot like on the 3000 335 3.3 305 3300 etc.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on February 02, 2015, 02:18:59 pm
I hope they start producing the large boots soon too.  I'd be shocked if they remain available from Poulan past this spring........
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on February 02, 2015, 06:33:18 pm
I was told the small boot is sought after right now 10 to 1 over the larger boot.  That could be because most of us know where to buy the larger boots already without having to ask the used markets if they have any.

I have sent a large one in for aftermarket measurements down the road by the member here that is having this stuff done up.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on February 02, 2015, 08:42:29 pm
I was told the small boot is sought after right now 10 to 1 over the larger boot.  That could be because most of us know where to buy the larger boots already without having to ask the used markets if they have any.

I have sent a large one in for aftermarket measurements down the road by the member here that is having this stuff done up.

That is great news.    I have a lot of saws that use those parts.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun on February 04, 2015, 01:39:17 pm
Quote from: hotshot
here's the direct link to save for the SKF-Chicago Rawhide seal identification,  use
the "Seals North America Part Look up".  I noticed that their pictures are not of the same exact seal, so don't be surprised
if you see something different there than what you pulled off the saw.
They also have a search engine, on that same page, but the dam thing takes exact thousandths of an inch
as an input to get a part number hit...pain in the butt.   A little saw seal is usually 0.003" to 5 over bore size, so you have
to keep guessing.

http://www2.chicago-rawhide.com/popup_parts_lookup_457010.htm

http://www2.chicago-rawhide.com/
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on February 04, 2015, 01:47:08 pm
I have used that site before and it does work well in my opinion.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Hoggwood on February 20, 2015, 05:29:09 pm
Apparently I was able to order some 530019146 seals for my 335 for $2.10/seal.  I grabbed 4.  The supplier confirms they are shipping to me.  I will inquire about availability of more.  I am guessing there must be stock somewhere else they are pulling from as I was under the assumption they were backordered and/or going the way of NLA.  I don't know enough to say whether a fellow ought to "grab 'em while you can". 

I will inform shortly and/or pickup more if anyone is interested. 

Cory
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on February 20, 2015, 06:38:04 pm
I would get them while you can.   If they are not NLA it will not be long and they will be.
I should get some myself.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on February 20, 2015, 08:10:08 pm
Apparently I was able to order some 530019146 seals for my 335 for $2.10/seal.  I grabbed 4.  The supplier confirms they are shipping to me.  I will inquire about availability of more.  I am guessing there must be stock somewhere else they are pulling from as I was under the assumption they were backordered and/or going the way of NLA.  I don't know enough to say whether a fellow ought to "grab 'em while you can". 

I will inform shortly and/or pickup more if anyone is interested. 

Cory

Cool info Shep. I just did a fake check out and it filled the order for 20 +. So they must be back in stock.   @ OrderTree
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on February 20, 2015, 10:35:08 pm
Back in stock at Ordertree?  Sweet.  I'll order some tomorrow.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Hoggwood on February 21, 2015, 02:13:37 am
Confirmation through tewarehouse that there are more.  FWIW, full line of Poulan parts and extensive selection of other general kits, filters, line etc.  For a Canadian the pricing is excellent and shipping is flat rate. 

Picked up some some quad rings for the 3400-4000 series and seals, handle start and grip insert for the sd25a. 

No hidden cache of carb boots though.  I did inquire.

Cory
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on March 07, 2015, 01:17:36 pm
Cant remember who was looking for this.

Poulan  4200 4400 4900 5200 5400 sprocket bushing 530032003 nos oem


http://www.ebay.com/itm/Poulan-chainsaw-4200-4400-4900-5200-5400-sprocket-bushing-530032003-nos-oem-/400862558901?pt=LH_DefaultDomain_0&hash=item5d55453ab5
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on March 07, 2015, 03:16:31 pm
I saw that listing.  I was looking for the inner clutch bearing race for my 8500.  The 8500/7700/6900 (the third/final generation of this saw series) used a different race, bearing, clutch drum, clutch washers, and clutch hub than the first and second generation saws (4200/5200, 4400/4900/5400) however. 

Because of that, the bearing race in that listing (and those in my 4200/5200 parts stash) won't work on my 8500.  The third generation saws use # 530032085  Luckily, a fellow recently sent me the complete clutch from an 8500 parts saw that he just needed for the cases.  Thanks to Patrick/Tractorsaw!!!  I am going to measure that bearing race and track down the timken part # for it for future reference.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on March 07, 2015, 03:20:00 pm
I ordered some 335 crank seals for future use.   Got them in already.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on March 07, 2015, 03:25:37 pm
I ordered two extra seals along with the boot and seals for the PP380 that I'm working on now.  Should have gotten another 'big boot' and a few more seals at the same time.  At least I have two spare seals in case another saw from this series pops up.

Will likely place another order next week and will likely put that 'spare' boot and a couple more seals on the list.  It's nice that the same seals were used for the whole series (unlike the boots........where there are two different ones).
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on March 09, 2015, 02:15:20 pm
You guys see those last 2 NOS small intake boots on bay sell for $35 apiece. Didnt last long either (back in Dec).  I just couldnt do that high even to set back.

Have been doing some back searching and there is a couple sellers out the gouging the heck out of poulan prices. 
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on March 09, 2015, 02:40:50 pm
You guys see those last 2 NOS small intake boots on bay sell for $35 apiece. Didnt last long either (back in Dec).  I just couldnt do that high even to set back.

Have been doing some back searching and there is a couple sellers out the gouging the heck out of poulan prices. 

There certainly are.  Have you seen the sellers (believe there are two) that have been listing starter pulleys for Poulan 4000 (and PP375-395) saws for $45-$70 EACH?  One of those sellers is listing an NOS Poulan Micro auto oiler check valve for $25.  That's highway robbery.  They're taking advantage of folks who want to get their old saw back up and running.  That one seller is an AS member too IIRC.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on March 09, 2015, 02:51:51 pm
I was thinking one was on AS.

Yep seen the valve.  I would give someone a used one if needed to keep them from getting ripped off by these folks.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on March 09, 2015, 03:16:26 pm
This is the seller who's on AS and SH.  Some of his prices are reasonable...........while others...

http://www.ebay.com/sch/satgtx/m.html?item=151613572370&rt=nc&_trksid=p2047675.l2562



This is actually 'reduced' from where he had it previously...

http://www.ebay.com/itm/NOS-POULAN-chainsaw-pulley-starter-530026371-375-4000-395-NEW-NOS-/151601568379?pt=LH_DefaultDomain_0&hash=item234c285a7b






Here's the valve...

http://www.ebay.com/itm/Poulan-chainsaw-oil-pump-Check-valve-530069142-NOS-NEW-1800-2000-2300-/151613572370?pt=LH_DefaultDomain_0&hash=item234cdf8512

Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on March 09, 2015, 05:01:10 pm
I believe they know that some of these parts are NLA or they are going to be, so they price gouge the heck out of buyers.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Eccentric on March 09, 2015, 06:46:55 pm
Yep.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on March 25, 2015, 07:24:37 pm
More crank seals came in on my ordertree order. couple big intake boots, rings for 54cc gasket kit circlips and forgot the blasted 60cc rings.  $9.99 for shipping a 1st class package only draw back.

Going to get my 60cc rings for $2.60 apiece and shipping $3something at mowers4u.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on March 25, 2015, 07:59:22 pm
More xcrank seals came in on my ordertree order. couple big intake boots, rings for 54cc gasket kit circlips and forgot the blasted 60cc rings.  $9.99 for shipping a 1st class package only draw back.

Going to get my 60cc rings for $2.60 apiece and shipping $3something at mowers4u.

That is good news.    I have some crank seals coming and already have a couple of the large intake boots.   I should get some of those circlips.   I have a spare carb also.   The rings I think I have a couple of sets too.   I should check on those since they are so cheap.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on March 28, 2015, 07:34:47 pm
Dang Mowers4u is fast. 60cc rings showed up today.  Combined the shipping so $3 and change shipping.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun on April 26, 2015, 09:52:38 am
Gregg had told a guy to just get the 60cc piston from ordertree  8). The guy comes back and say shows NLA  :o.  I went and checked and SOB it is.  :'(

Poulan 365 3500 3750 380 piston NLA now too   530069549  :(
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on April 26, 2015, 12:50:52 pm
That sucks.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on September 27, 2015, 08:43:07 am
Digging in this thread for that one Roger tried.  There was something about the low psi it would hold.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: 3000 FPS on September 27, 2015, 09:41:29 pm
Digging in this thread for that one Roger tried.  There was something about the low psi it would hold.

That was on page 6 and 7 Kevin.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on October 17, 2022, 10:12:47 am
Poulan oem crank seal compared to a boat motor boat seal found.  He is going to install a set to see if it hold up.

There is a guy that works on boat motors. He found a seal that matches oem specs pretty close.
So he sent some to a guy in my CR group. He is going to install in a saw and test out to see.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on October 17, 2022, 10:15:00 am
Poulan OEM crank seals I have left 7   530019146

Placed a order with a distributor this morning to see if I could get 20-40 more.  They are a in between from Poulan to dealers.  Most dealers show NLA and Poulan NLA

But these show siting there.



Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on October 18, 2022, 05:56:55 am
Oh I ordered 40 crank seals like used for the 2700 2800 3300 365 3500 330 3450 380 etc etc. Just in case someone else might need. I was down to 7 left.
Mostly showing NLA except for 1 here and there. But found some at a distributor. The go between from poulan to dealers. Now to see if they can actually fill the order.

They show shipped now.
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on October 18, 2022, 01:31:28 pm
Been talking with a new member else where. Gary welcome to the group. 
 Gary come across a boat evinrude gear case seal that is close to same as the OEM poulan seal in the PP330 3300 365 etc etc etc.  He sent 2 to Boedy to put in a saw to test and see if they work. 
He offered to send me 2 but I have OEM on hand and OEM on order so waiting to see. LEFT side OEM.
This is just a back up plan in case the 40 OEM I ordered that has been shipped it says and dont pan out. 🤞

Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: Cut4fun . on October 21, 2022, 10:46:38 am
No reason for those boat seals just yet.  Here is 40 OEM poulan crank seals I just ordered.

Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: The Ripper on November 02, 2022, 09:28:50 am
 Do you have any of these seals still available? and how much
Title: Re: NLA Poulan Parts 2700-3600 3450-3750 PP330-380 Crank Seals etc
Post by: The Ripper on November 02, 2022, 09:52:21 am
Found some seals, and knew I should have started a stock of parts for this particular Poulan saw.