Chainsaw Repair
For Sale - Wanted - Trades - Swaps - Stolen - Recalls - Lost => Trades Swap Section => Topic started by: Cut4fun on February 14, 2015, 12:54:30 pm
-
If you run .404 or have a 3/8 tip.
http://www.ebay.com/itm/32-Poulan-Sprocket-Nose-Guide-Bar-/111578118310?pt=LH_DefaultDomain_0&hash=item19fa92f8a6
http://www.ebay.com/itm/36-Poulan-Sprocket-Nose-Guide-Bar-/111578119624?pt=LH_DefaultDomain_0&hash=item19fa92fdc8
-
Anyone tell the bar mount on 36 etc?
-
Windsor UXL. That's basically the same as an Oregon D096. 3/8" (9.5mm) slot. Homelite XL-series mount. SXL-AO, SXL-925, 450/550/650/750, etc. The UXL bars I've seen also have oil passages from the adjuster slots to the chain groove (in addition to the separate oil holes). They can be used on a later XL-series (3/8" stud) Homelite, a Poulan 6900/7700/8500, or a late (3/8" stud) Poulan 4400/4900/5400 (some of those were equipped with 5/16" studs, others with 3/8" studs).
Windsor never made an A176/D176 type 5/16" slot Homelite/Echo/Poulan/etc mount bar. Instead, they sold the UXL mount bars with an 'S' type stud spacer for use on 5/16" stud saws. That's how these bars were supplied for Poulan. I have a 306A that came to me with a 20" UXL mount bar and an 'S' clip. Has the Poulan part # that's in the IPL. The IPL's show these bars and the 'S' clips. The piece of masking tape across the stud slots of the bars in the ebay listings held the 'S' clip in place until the bar was sold. Can't see if the 'S' clips are still there.............or if they have escaped.
McCulloch did a similar thing with some Oregon and Windsor manufactured bars. They have a 3/8" stud slot (suitable for the large frame Macs so long as they have the right bar plates), and were sold with spring type stud spacers held in the slot with tape.
http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/c0ac3eaf85163b9c88256e0e001fa1fe?OpenDocument
(http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/c0ac3eaf85163b9c88256e0e001fa1fe/Body/0.84?OpenElement&FieldElemFormat=gif)
-
I have a bunch of those 3-rivet 3/8" pitch Windsor tips. Could sell/trade some if needed for these bars. The current 5-rivet Windsor tips won't work on those older Windsor bars.
Kevin I went through his items index. I think I see what got you to his listings. 8)
He also has the bare bore version 46cc cylinders (and the corresponding pistons). Wish he had the chromed bore versions. I put those into Husky 36-141 saws (with some intake side parts mixing/matching as well).
He does have pistons for the 49cc clamshell Poulans (like the 50th anniversary 315 in another thread here). I wish he had the cylinders for those. I want to put one of the 49cc P/C's into a Husky 36-141 series saw like I do with the 46cc versions.
He also has cylinders for the PP235 and PP236. Unfortunately he doesn't have pistons too.
-
Thanks for that info. Yep came across bars in other searching. ;)