Chainsaw Repair

Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Echo => Topic started by: Cut4fun . on September 29, 2015, 05:38:54 pm

Title: echo cs-310
Post by: Cut4fun . on September 29, 2015, 05:38:54 pm
Had echo 310  dropped off today.  Reminds me of my echo 3900 physical size wise.   8)

Any known issues and tuning specs? Max rpm etc?

Guessing 31cc
Title: Re: echo cs-310
Post by: Cut4fun . on September 30, 2015, 12:31:39 pm
@mountainlake or others that know.  Whats the good bads to watch and check on these?
Title: Re: echo cs-310
Post by: Nathaniel Vansickle on September 30, 2015, 07:27:52 pm
L mixture needle : 2 1/2, H mixture needle : 2 1/4  13k

only real problem i have had with them is the tank breaking at the front A/V mount/wrap handle mount. other than that they have been fairly reliable and run ok after a mm
Title: Re: echo cs-310
Post by: Cut4fun . on September 30, 2015, 07:29:09 pm
Thanks Nate.  I was holding off digging in till I got some info.  The L and H is good to know it is one of those. ;)
Title: Re: echo cs-310
Post by: Cut4fun . on October 01, 2015, 05:53:47 pm
OK going to be truthful. Not impressed.  :o

I had to make sure it was 31cc = 30.5cc shown on tag. Saw is like new too.

I was just expecting it to be a little closer to my 39cc echo 3900.  I sure hope the echo 400 run little closer to the 3900 as the 310 isnt even  close.   :o
Title: Re: echo cs-310
Post by: mountainlake on October 02, 2015, 07:43:08 am

 I'm not impressed with the build quality of the 310  352 saws either and don't know how they run yet, I have one to put together .  The CS400 saws are real good runner and built good.  Steve
Title: Re: echo cs-310
Post by: Fishnuts2 on October 02, 2015, 10:48:10 pm
The 352 runs a lot better than the 310, they are quite different than the CS-400 though. I use the 352 often  limbing small stuff.


Sent from my iPhone using Tapatalk
Title: Re: echo cs-310
Post by: stubnail67 on October 09, 2015, 08:36:01 pm
what size bar ya have on the cs 310? 14 inch?
Title: Re: echo cs-310
Post by: Cut4fun . on October 09, 2015, 09:01:14 pm
what size bar ya have on the cs 310? 14 inch?


Thats what was on it.   I was only cutting maybe 6" cherry at best. Just a dog this one was.

The little 30cc poulan 1800 would takes its lunch IMO.
Title: Re: echo cs-310
Post by: stubnail67 on October 09, 2015, 09:14:46 pm
Dam i was going to buy one to add to my echo  line up.... maybe i should keep my poulan 2600.....
Title: Re: echo cs-310
Post by: leec on January 27, 2016, 09:38:18 pm
The CS370 is supposed to be a ripper!
Title: Re: echo cs-310
Post by: leec on March 24, 2016, 03:01:43 pm
I should be picking up a 310 next week, if it's not all scored up.  I'll let you know how it goes.  Also 2 more 440s