Chainsaw Repair

Chain - Grinders - Filing - Wood Milling - Tools - Welding - Machinist - Mowers - Tillers => Chain - Bars - Grinders - Filing => Topic started by: Cut4fun on January 14, 2016, 03:37:02 pm

Title: ? 66DL 325 050 bar ideas
Post by: Cut4fun on January 14, 2016, 03:37:02 pm

I stepped in it trying to come up with a D009 66DL 050 325 bar for testing chains.  No such critter I can locate so far. 
So I started looking a D176 mount that I could mod over to D009 for my testing uses.

I have small mount bars in 66DL but looking for the large mount.

Any ideas? Maybe sprocket nose swap?  Would a 60DL 3/8 switched to 325 nose be 66DL. 

Help me out on my rednecking  :P

Title: Re: ? 66DL 325 050 bar ideas
Post by: mdavlee . on January 14, 2016, 03:45:23 pm

I don't know for sure. I have a carlton 16" .050" in large mount.

Title: Re: ? 66DL 325 050 bar ideas
Post by: Cut4fun . on January 14, 2016, 04:13:49 pm

I need to go through my bars this weekend. That ought to be fun. Least all hanging up or on saws.

Title: Re: ? 66DL 325 050 bar ideas
Post by: Cut4fun . on January 14, 2016, 08:22:52 pm

Quote from: Gatekeeper on January 14, 2016, 03:45:23 pm

I don't know for sure. I have a carlton 16" .050" in large mount.

What I have come up with.  ::) :P

I think I will try and find a stihl mount bar in 325 050 67dl and then cut on it alittle at the rear to fit 66dl and bigger gear if go with 9T or not. Guessing right now to stick with 8T.
Use adapters to fit my big poulans with D009 mount.

Crap part is I had some 325 050 16" and gave them away basically.

Anyone have a used but not getting used bar for this project?

Title: Re: ? 66DL 325 050 bar ideas
Post by: 3000 FPS on January 14, 2016, 11:33:18 pm

Quote from: Cut4fun . on January 14, 2016, 04:13:49 pm

I need to go through my bars this weekend. That ought to be fun. Least all hanging up or on saws.

I was going to look at what I have this week end also.

Title: Re: ? 66DL 325 050 bar ideas
Post by: Cut4fun . on January 15, 2016, 12:37:55 pm

I recall now the stihl was a pita on off with even the right dl count.  Thinking tail mount was longer or something. Will need to test and see with my 16" 3/8 bar what was up.

(http://i59.photobucket.com/albums/g289/doemaster789/415/p3450x3p30p475%20008_zpsnmvkugsa.jpg)

Title: Re: ? 66DL 325 050 bar ideas
Post by: SawTroll on March 01, 2016, 03:40:58 pm

Quote from: Cut4fun on January 14, 2016, 03:37:02 pm

....   Would a 60DL 3/8 switched to 325 nose be 66DL. 

Help me out on my rednecking  :P

At least with Tsumura it will be 68dl, with an 11t nose 3/8" converted to 12t .325.

The source of that info is assumed to be reliable, and has posted it several times.

Title: Re: ? 66DL 325 050 bar ideas
Post by: Cut4fun on March 01, 2016, 08:08:18 pm

Were good for bar now Niko so it dont matter.  Went small mount instead.

Title: Re: ? 66DL 325 050 bar ideas
Post by: 3000 FPS on March 01, 2016, 10:39:57 pm

 I looked at what I had Kevin but did not have what you need.