Chainsaw Repair

Husqvarna - Stihl - Poulan - Jonsered - Dolmar chainsaws and more => Poulan => Topic started by: Cut4fun . on December 31, 2018, 02:17:32 pm

Title: NOS poulan parts Used poulan parts
Post by: Cut4fun . on December 31, 2018, 02:17:32 pm
Cant find the old thread. 

Pulling some nos and used parts for 4-5 folks today.

Title: Re: Poulan NOS used parts
Post by: Cut4fun . on April 30, 2019, 11:23:42 am
Poulan NLA parts for some folks. One air filter had some thin spots in the flocking. I just use sealall to seal those areas off.

Title: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 11, 2020, 09:36:57 am
There is a guy selling a ton of poulan nos parts in the CRG.  Bow parts etc etc etc.

Thought of a few of you since you like to restore with decals.

Title: Re: NOS poulan decal sticker
Post by: Fishnuts2 on February 11, 2020, 09:54:56 am
I'm not on FB, but does he have a decal for a 53?
Title: Re: NOS poulan decal sticker
Post by: Cut4fun . on February 11, 2020, 12:17:13 pm
I'm not on FB, but does he have a decal for a 53?

What you see in the 100's. 
Title: Re: NOS poulan decal sticker
Post by: Fishnuts2 on February 11, 2020, 09:06:25 pm
Could you send me a link to these parts?
Title: Re: NOS poulan decal sticker
Post by: Cut4fun . on February 12, 2020, 07:41:58 am
Could you send me a link to these parts?

Cant sent actual link right to his post.  Least I'm not smart enough to.
Here is where he has started posting them.  chainsaw repair group facebook https://www.facebook.com/groups/415662708518445/
Title: Re: NOS poulan parts cylinders pistons
Post by: Cut4fun . on February 12, 2020, 09:02:09 pm
Picked up some NOS poulan cylinder pistons in boxes today. Some I know some I need to research.

Title: Re: NOS poulan parts
Post by: Cut4fun . on February 13, 2020, 09:24:17 am
Quick check of the 2 boxes worth before calling it a day. Like 5mins of a check   :D


One I think is a nos 335 c and the piston says 335 but it isnt thin ring. So might be a the 335 predator single ring piston.
Seen a nos 295 c and p with lower clam. Think couple of pioneer nos pistons too. Others no clue.
Some weedwacker stuff. No interest in those whatsoever. 
1 coil
Think a couple pioneer nos piston in the white boxes

Title: Re: NOS poulan parts
Post by: Cut4fun . on February 13, 2020, 12:08:54 pm
Now to see if I was right on some and what the heck some are. 

Title: Re: NOS poulan parts
Post by: Cut4fun . on February 13, 2020, 01:21:56 pm
Think I got them all figured out but 1. Some of the ones I thought poulan, were pioneer x3 cylinders. P28, then WT coil, K650 partner cyl, P 3450 T1, P 2750 2775 295, PP114, gasket K650 700, Piston 336 3450 330, 2775 2750 295, P26-P28? and one I cant figure pioneer 475350 or 507475350

Hmmm forgot to write # down for 1. Got more in pic then wrote down. LOL

All I could find on that weird clamshell looking thing  36zd3 38cc   Bingo jonsered 370
Title: Re: NOS poulan parts
Post by: Cut4fun . on February 13, 2020, 04:59:17 pm
Chipsflyin found this. P26 piston #507475350, ( Jacks Small Engines ) NEW- $12.78+ shipping"

Edit:
The cylinder that goes with is # 507431400

I told him this  - Only difference I noticed in the 2 Pio pistons. One of then had one side with narrower skirt. Both went into all 3 cylinders same fit it seemed.
Title: Re: NOS poulan parts
Post by: Cut4fun . on February 14, 2020, 07:42:11 am
The last piston come back to P26. Only difference I see in it and other piston I think is P28 is one skirt on the 26 is narrower. The 3 cylinders came back to P29 and or P26. I dont know these saws at all.
The Partner 650 cylinder should bolt right up to P55 P65 650 700 7000. PP114 is a polesaw, Jred 370 cylinder, Poulan 2750 PP295 cylinder and piston. Only stuff I see for my uses is the is the Poulan 335 3450 P+c stuff.

So if some poulan, pioneer, partner folks need something for a restore.  I dont do that ebay high price crap some do. I will practically give what I dont want away. ;)
Title: Re: NOS poulan parts
Post by: Fishnuts2 on February 14, 2020, 09:37:49 am
If one of those cylinders fit a Pioneer 1073 I'd be interested.
Title: Re: NOS poulan parts
Post by: Cut4fun . on February 14, 2020, 02:40:46 pm
If one of those cylinders fit a Pioneer 1073 I'd be interested.

Only Pioneer is 26 28
Title: Re: NOS poulan parts
Post by: Cut4fun . on April 25, 2020, 01:33:51 pm
Was digging today for someone in need.

Checking my last 2 54cc saws before committing any of my 46.5mm pistons. Only used p I have left not sellers. 4 3450 330 cylinder in used left. One super nice. Have one 3.3 54cc 335 NOS p+c set. P would work but like to keep that set together.

Guy on the chainsaw repair group FB was wanting a nice set for a restore saw for a friend.

Forgot about these. Looks like 3 good 46.5cc 54cc pistons possibly.

Imo best set off those 3 above. Like new
Title: Re: NOS poulan parts
Post by: Cut4fun . on April 25, 2020, 01:38:29 pm
Also dont forget I have a new poulan 295 cylinder and piston set. I will ever use these if someone wants to trade or buy.

Title: Re: NOS poulan parts
Post by: Cut4fun . on April 26, 2020, 07:06:33 pm
Last pics before trading off to help the guy with build.


Poulan 330 piston and cylinder in nice shape
Title: Re: NOS poulan parts
Post by: Cut4fun . on May 12, 2020, 01:05:37 pm
Just saving pics of some poulan parts. There is tons more not in pics.
Taken of just these series.

Somebody asking me to part with one of my 3.3 335's I havent finished putting lines in yet. Have 3 runners already. Bought them for parts. But will be runners easy.
Title: Re: NOS poulan parts
Post by: Cut4fun . on May 12, 2020, 01:06:06 pm
1 more

Title: Re: NOS poulan parts
Post by: 3000 FPS on May 12, 2020, 11:46:12 pm
That is a lot of parts.   
Title: Re: NOS poulan parts
Post by: Cut4fun . on May 18, 2020, 08:51:10 am
Was showing a AS member this poulan 335 predator 330 3450 46.5mm piston.  We are thinking someone put a bare piston in a 3300 bare bore cylinder. He said 360 scoring.   Not thinking straight gassed.

Just saving this NOS piston pic

Title: Re: NOS poulan parts
Post by: Cut4fun . on June 10, 2020, 11:59:30 am
If the poulan 505 leaves Sunday.

This poulan 505 475 445 425 415 jonsered 2077 2083 2083II full wrap handle can be sold.   Big dawgs to sell too to install full wrap too.  What I got in them. PM if interested.

Might sell the other one off the PP445 too. 


Back left in pic.






Title: Re: NOS poulan parts
Post by: Cut4fun on June 11, 2020, 07:20:04 am
If someone was wanting one of these NLA new west coast set ups.

Full wrap handle for Poulan 415 425 445 475 505 Jonsered 2083 2077 2083ll Partner 7700 710 660. Big west coast dawgs needed to mount full wrap handle on these. Inner and outer.

Nicest one of my 2 full wraps.

Will also be in the for sale board here.

Title: Re: NOS poulan parts
Post by: Cut4fun on June 12, 2020, 07:32:45 am
All of this style poulan air filter NOS I have left. Still have some used too.

Title: Re: NOS poulan parts
Post by: Cut4fun . on June 14, 2020, 07:41:02 am
 Both FULL wraps and dawgs etc SOLD

PP445 will be next. One of them for  with nicest 445 covers.  Prob the one I didnt have to redneck repair the case by muffler.  One in pic that had full wrap.
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on June 21, 2020, 10:34:21 am
Freaking run yesterday digging up used poulan parts for folks in the CRG

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on June 25, 2020, 11:20:15 am
Collectors wanting my poulan rollernose bars. So got them out.

Guessing 14" being 16 1/4" long.  One 1/4" chain was 77DL. Didnt count the other 2.

Had 3 sets of bars and chain. 1 set already sold and shipped.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on June 27, 2020, 08:15:19 am
Nos poulan clutch cover and recoil cover and some used ones too.

Was digging out some parts to throw a recoil together to test a redneck idea I seen on CRG. ;)

Was surprised how well it does work. Even matches the 372 cover I done to test to see.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on June 27, 2020, 03:02:40 pm
Showing folks the NLA poulan pulley in shallow , deep and later

How the deep could go on the guys 3300 with the shallow set up with same flywheel. If he had a deep cover too.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on June 27, 2020, 03:04:51 pm
Had to laugh after setting up the recoil right and setting saw back on shelf. Least now another whole recoil to use.

Title: Re: NOS poulan parts Used poulan parts
Post by: 3000 FPS on June 28, 2020, 12:12:49 am
Looks like you are really cleaning house. 
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on July 29, 2020, 11:36:07 am
Pulling some parts for folks. 2077 2083 415 475 445 505 425 oil pump oiler, crankshaft, cylinder, NOS piston and used clutch.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 01, 2020, 10:50:19 am
Pulling some NLA used AV's today for a guys build.

Hope there is some aftermarket ones in the works for the lower rubber AV's. 


Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 14, 2020, 10:53:51 am
Dealer in my CRG FB looking for some parts today. So pulled these out to offer him.

Poulan 335 Predator  NOS cylinder and piston

Poulan Pro 295 new piston and cylinder set.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 15, 2020, 12:47:55 pm
Pulling some parts for a guys 475.

Handle insert

Cass for  brake

Handle brace

Outer metal cover plate





Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 15, 2020, 12:51:55 pm
My last poulan pulley for 3450 3750 380 330. He was also needing the spring.  Put together in a 3450 recoil to be ready to bolt on for him.

SOLD

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 16, 2020, 02:17:52 pm
Thread pieced together from CRG FB.

Trying to take stock in what I got as runners in the 49cc - 54cc  poulans with mag cased.  The tagged 49cc is sold. 
Any of the others can go except for the one dad bought new in 1993.
Also think I just found a parts saw with a good 330 380 3750 3450 pulley.  So may have one more left.
Now trying to figure out what I want to build next.

I thought I had 5 of those black with blue decal 54cc ones. Found the first one I ever bought of those hiding.

5 runners. The last 4 were bought for parts for the first one I bought. But all just needed minimal work to be runner again too.

Yep another good pulley. This was a 380 60cc I sold carb and topend off of. But had used a 330 recoil testing it out year back.

Betting I just found a HDA137 carb. Forgot about this 380 I never fixed. Will know for sure in a sec. could be a 164 but all 380 I have seen had 137.

Hot dang it is the better of the 2 big carbs. HDA-137



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 16, 2020, 02:19:19 pm
2 more I couldnt add above.

Betting I just found a HDA137 carb. Forgot about this 380 I never fixed. Will know for sure in a sec. could be a 164 but all 380 I have seen had 137.

Hot dang it is the better of the 2 big carbs. HDA-137

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 18, 2020, 08:00:44 am
Pulled the poulan pulley from 330 recoil to put in 380 recoil for CRG member.   SOLD

Also pulled poulan 380 yellow tank SOLD

Walbro HDA-137 car from same 380 SOLD

Poulan 2800 muffler etc models requested. 

Plus the have broken metal part pulley that is still usable for 330 380 3450 3750. I kept it for a back up. Better then nothing.
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on September 21, 2020, 04:53:27 pm
52mm that came off jonsered 2077 with air injection.  Can be used on poulan 475 and partner 7700 without AI.  Plus all he others in series. 
Somebody had used black sealer etc under the dang intake boot and on cylinder intake too.  Had to take a wire wheel to get that crap out of the groove.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on October 09, 2020, 09:17:32 am
Local guy said he had been looking for poulan 365 pulley for 2 years.  :o

I contacted him when I seen his wanted ad. Gave him my card if he ever runs into hard time finding NLA parts again.


Starter pawls they use.

Bottom 2 now sold.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on October 13, 2020, 08:27:48 am
Poulan 1800 2000 2300 coil  530069202
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 09, 2021, 08:46:12 am
Poulan 415 425 445 475 505 clutch cover metal SOLD

Jonsered 2077 with air injection cylinder SOLD.
Gave the used piston to them too.

NOS Poulan clutch cover metal SOLD

Lot of stuff pending and holding for folks.

My last 2 runners are first 415 that was sold new with partner air filter cover and the updated tanks and air filter set ups. Then my first 445 and both at lost fights to trees before I got them and redneck the busted case areas. Both topends still like new etc.
Once their gone I then will be selling of the NLA hard to get parts too.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 09, 2021, 01:50:09 pm
Poulan chain brake cover grey for 365 330 380 3750 3450 etc etc etc




Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 09, 2021, 02:01:24 pm
Last NOS one shipped out today.

Metal.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 10, 2021, 02:59:48 pm
Pulled a tank from a 330 to help a guy out that has one with a seam leaking.

This is the saw I tested as a ported 380 with 24" 3/8 buried at one time. Then tore down and started parting it out.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on February 13, 2021, 08:13:40 am
Pulled these like new poulan 3300 3000 2800 etc flocked air filters from some parts saws.  To help a guy out with a neighbors craftsman 2.8 and his 3.3

(http://chainsawrepair.createaforum.com/index.php?action=dlattach;topic=7606.0;attach=30857;image)
(http://chainsawrepair.createaforum.com/index.php?action=dlattach;topic=7606.0;attach=30859;image)

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on February 17, 2021, 07:32:43 am
Poulan NOS replacement chain brake cover.  Grey like a lot  of their replacement parts.

330 380 3450 3750 3500 365 3000 3300 etc etc fits them all in this series.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 18, 2021, 12:48:46 pm
Just showing someone these NOS chain brake covers fit all in these series of saws.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on February 19, 2021, 08:51:20 am
NOS poulan clutch cover is SOLD  330 380 3500 365 etc etc 
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on February 19, 2021, 11:51:14 am
Update: was just packing up and noticed 2 of the parts show made in Canada.




Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on March 05, 2021, 10:37:32 am
Sold a outer dawg so I needed to pick up some more NOS parts.

Poulan spikes dawgs medium inner outer

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on March 09, 2021, 02:35:36 pm
2 runners and alot of NLA parts today for a big thing that went bang.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on March 10, 2021, 09:12:43 am
Canadian in the CRG FB said he needed a pto case half. So I split one for him yesterday.



Title: Re: NOS poulan parts Used poulan parts
Post by: 3000 FPS on March 10, 2021, 09:25:40 pm
There you go.   More parts.
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on March 11, 2021, 07:19:26 am
Learned one thing. Dont split a case before you been paid.  ;)

But dont really matter I have a 2 PP380 parts saws and one needs the pto side.  But I will prob never get to those.
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on March 27, 2021, 08:52:18 am
Shop in FL needing a coil for the blue black 3.3 like I like.   

Used and found a NOS coil in bin I forgot about. Used SOLD



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on April 12, 2021, 07:24:13 am
425 445 505 updated air filter base and air filter to go on a updated tank 425 445 505  for a 475.


SOLD


Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on April 14, 2021, 11:04:48 am
Few more folks asking for more parts. So will just show them here to a couple folks too.

newer, shallow, deep pulleys. 3 60cc pistons but all have scuffing. I know the one out of 380 I could use myself with some cleaning a new ring.

PP330 clutch cover does have new band. But for guy up north. Shipping will be more then cover. Just so you know.

NOS filters and used still. NOS intake boots and used.

Have few 415 425 445 505 cylinders etc

Yes on the 32mm stroke cranks for the mag cased ones I like.

If I missed request just ask and I'll take more pics if still have parts.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on April 14, 2021, 11:05:13 am
1 more

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on April 15, 2021, 03:57:54 pm
Pulling parts for folks.

3 flocked ones SOLD

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on April 15, 2021, 04:00:29 pm
330 380 3750 3450 pulley

3300 etc pulley

365 3500 3.7 pulley

3.3 recoil

60cc used poulan piston

SOLD

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on April 27, 2021, 03:31:57 pm
Done for now doing the back exit and front exit mufflers for saws sold.


These are the front exit ones I had left over.  They are matched with their right oem back halves. 

One has seen better days. But a guy knowing how to weld can fix that one easy.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on April 28, 2021, 08:40:39 am
Done for now doing the back exit and front exit mufflers for saws sold.


These are the front exit ones I had left over.  They are matched with their right oem back halves. 

One has seen better days. But a guy knowing how to weld can fix that one easy.



That was a total surprise that they were on everyone's wanted list.

All 4 front exit mufflers spoke for.
Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on May 02, 2021, 10:31:29 am
Poulan clutch jonsered clutch

505 445 425 475 415 2083 2077



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on July 09, 2021, 04:56:48 pm
Poulan 8500 full wrap handle. Has the 8500 grip style.  Can be used on the 5200 5400 etc. from what I recall when I had the NOS full wrap ones. Just the type grips used was different between the 3.

Also picked on a 310 handle to hopefully talk the local into fixing the redneck repaired one soon.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on July 18, 2021, 09:45:01 am
Poulan clutch assembly set pulled to help a guy on a 3300.



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on July 21, 2021, 09:14:43 am
Poulan 380
530042080 Lower Isolator
530069384  Isolator Assembly Kit-Type II Only   This part replaces obsolete part and 530036962.
530030202 intake boot
952069321 brake kit



Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on July 28, 2021, 02:08:31 pm
Post for a guy asking. Poulan 3450 330 3750 380 clutch drum rim sets. These style drums allow you to run replaceable sprocket rims.
The normal to find 2 shoe clutch and the last HD 3 shoe clutch. Itís pricey and harder to find.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun . on July 28, 2021, 04:00:44 pm
Last ones I have.  Flocked and mesh poulan air filters NOS and used. About out.  NLA new.

Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on August 08, 2021, 08:57:14 am
1 poulan 3400 3700 3800 craftsman 3.4 3.7 pulley bare.  Some wear on the end of pulley because it was on a saw that had broken cover shaft. Allowed movement engaging.

1 poulan 3400 complete recoil starter pulley spring shell etc.

Pic for the folks asking.







Title: Re: NOS poulan parts Used poulan parts
Post by: Cut4fun on August 16, 2021, 09:56:16 am
What the inside looks like of the poulan 46cc clamshell saw.

New set I pulled for a guys PP295. They are on par with the 025 250 for lot less $$$


UPDATE - SOLD