Author Topic: 603 top end on 680 bottom end...  (Read 640 times)

0 Members and 5 Guests are viewing this topic.

Offline adam32

  • Piped Saw
  • *****
  • Posts: 429
  • Karma: 46

  • Total Badges: 24
    Badges: (View All)
    Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary Level 5 Linux User Third year Anniversary
603 top end on 680 bottom end...
« on: July 08, 2014, 10:12:22 am »
So I'm thinking I might try it for a 6 cube saw. A stock 603 has a 56mm bore and 42mm stroke so it's 103cc, just above 6 cube. So if I take that jug and put it on the 38mm stroke 680 bottom end then it'll be 94cc, right in the middle of the class. Or stroke it to 40mm and be right at 99cc  ;D ;D ;D

The beauty of the 603 jug is the removable transfer ports  ;)

Share on Facebook Share on Twitter


Offline KilliansRedLeo

  • Nitro Hotsaw
  • *******
  • Posts: 2361
  • Karma: 80
  • Location: Rochester, NY
    • RoCHusqvarna

  • Total Badges: 29
    Badges: (View All)
    2000 post CR Staff One year Anniversary 1000 Posts Never Sleep Group
Re: 603 top end on 680 bottom end...
« Reply #1 on: July 08, 2014, 01:27:09 pm »
Adam, that REALLY sounds like a neat project! Keep going!
"When the people fear the government...you have tyranny....When the government fears the people....you have liberty"

Thomas Jefferson
1743-1826

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

  • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 603 top end on 680 bottom end...
« Reply #2 on: July 08, 2014, 03:51:17 pm »
Have you tried doing it the other way around? Smaller 680 jug on the longer stroke 603. Could have a lot of torque with the extra stroke.  Rod the same length?

Offline adam32

  • Piped Saw
  • *****
  • Posts: 429
  • Karma: 46

  • Total Badges: 24
    Badges: (View All)
    Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary Level 5 Linux User Third year Anniversary
Re: 603 top end on 680 bottom end...
« Reply #3 on: July 08, 2014, 05:15:33 pm »
Have you tried doing it the other way around? Smaller 680 jug on the longer stroke 603. Could have a lot of torque with the extra stroke.  Rod the same length?

I did try that a while ago, it ran for a couple minutes too lol. I need to make a better spacer and figuring out the port timing was a pain in the azz, I tried several 52mm pistons, even made a couple pop ups to try.

Offline aclarke

  • Nitro Hotsaw
  • *******
  • Posts: 1676
  • Karma: 172

  • Total Badges: 25
    Badges: (View All)
    Fourth year Anniversary Third year Anniversary 1000 Posts Second year Anniversary Level 5 500 Posts
Re: 603 top end on 680 bottom end...
« Reply #4 on: July 08, 2014, 10:36:41 pm »
Ok.  The big jug route might be easier do they both have a
"spigot" on the cylinder or flat?

Offline adam32

  • Piped Saw
  • *****
  • Posts: 429
  • Karma: 46

  • Total Badges: 24
    Badges: (View All)
    Sixth year Anniversary Fifth year Anniversary Fourth year Anniversary Level 5 Linux User Third year Anniversary
Re: 603 top end on 680 bottom end...
« Reply #5 on: July 08, 2014, 10:47:27 pm »
Both have the spigot...thought about cutting it off...

 

Related Topics

  Subject / Started by Replies Last post
18 Replies
926 Views
Last post September 15, 2013, 08:34:15 am
by Jd2007