Author Topic: 2159W  (Read 648 times)

0 Members and 0 Guests are viewing this topic.

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1132
  • Karma: 81
2159W
« on: September 11, 2013, 08:15:44 pm »

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21880
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2159W
« Reply #1 on: September 11, 2013, 08:28:21 pm »
My cousin to it wasnt to bad in the firewood pile too.  smaller 56.5cc  though set 14.1k and off the reel stock square chain.

http://www.youtube.com/watch?v=IZJeepcpaN8

REDNECK Saw Repair Getter Done

Offline Playinwood

  • 6 cube
  • ****
  • Posts: 246
  • Karma: 5
Re: 2159W
« Reply #2 on: September 11, 2013, 10:40:06 pm »
2159
it was mine for a long time also..that saw has cut a pile of wood.

Be nice to her

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1132
  • Karma: 81
Re: 2159W
« Reply #3 on: September 15, 2013, 03:21:29 pm »
2159
it was mine for a long time also..that saw has cut a pile of wood.

Be nice to her

After this weekend I am going to see if it likes the 357 pipe. Should be interesting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21880
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2159W
« Reply #4 on: September 15, 2013, 03:27:39 pm »
I'm still trying to find the time to try a Bertrand 372 pipe on 2 372 woods ported work saws 76cc and 71cc myself. Just for chits and giggles to see if any gains at all.
REDNECK Saw Repair Getter Done

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1132
  • Karma: 81
Re: 2159W
« Reply #5 on: September 15, 2013, 03:42:32 pm »
I know the 2159 will sound good. Anything more will be a bonus. Didnt think you had any ported saws left.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21880
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: 2159W
« Reply #6 on: September 15, 2013, 03:46:31 pm »
I know the 2159 will sound good. Anything more will be a bonus. Didnt think you had any ported saws left.

I dont. Sold them both maybe 2 years ago, maybe last year, to a friend 20mins from me. Told him he should get that pipe from Simon. 8) ;D
REDNECK Saw Repair Getter Done

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 589
  • Karma: 72
Re: 2159W
« Reply #7 on: September 15, 2013, 08:02:34 pm »
the pipe will work alot better than the muffler even on gas but remember the pipe is not going to turn the same rpms as it does on alcohol

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1132
  • Karma: 81
Re: 2159W
« Reply #8 on: September 15, 2013, 08:18:28 pm »
Ed, how much more is left in the 2159? A change of a few degrees or start with a new jug?

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 589
  • Karma: 72
Re: 2159W
« Reply #9 on: September 15, 2013, 09:50:32 pm »
that 2159 for up here has alot left on the table compared to the same thing ported for up here , I'm sure the flywheel was never touched and the porting is lower than what I would run here , For down your way I would not touch the porting but tighten the squish as much as you can cause I'm thinking right now it should be .025 but there might be carbon on top of the piston . Next advance the flywheel, I built that saw in the beginning for Russ and he wanted it to be cooler than what he normally got. He was thinking of running a longer bar on it in the winter time when the snow got deep at his place

 

Related Topics

  Subject / Started by Replies Last post
11 Replies
1030 Views
Last post October 24, 2012, 05:25:54 pm
by Old Iron Logging