Author Topic: 2159W  (Read 1206 times)

0 Members and 51 Guests are viewing this topic.

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #10 on: October 19, 2013, 01:52:23 pm »
Playing around.


Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #11 on: October 19, 2013, 02:28:55 pm »
Still have to match the cyl exhaust outlet  to the pipe.

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #12 on: October 19, 2013, 02:49:25 pm »
Another video


Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #13 on: October 19, 2013, 08:07:52 pm »
A few pics

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80

  • Total Badges: 32
    Badges: (View All)
    Level 6 Linux User Mobile User Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary
Re: 2159W
« Reply #14 on: October 19, 2013, 08:33:28 pm »
well it least it runs not bad on the pipe , like I said its lower on rpms on a gas motor compared to a alcohol motor but that pipe sounds to be pretty good on the 2159 , donot worry about matching the ext. port to the pipe as its the other way , the pipe inlet is bigger than the 2159 ext port outlet , your not going to gain hardly anything matching the pipe to the port, advancing the flywheel abit will make a bigger gain

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #15 on: October 20, 2013, 12:00:09 pm »
Ed, any gains to be had with a carb upgrade?

Offline EHP

  • Gas Hotsaw
  • ******
  • Posts: 637
  • Karma: 80

  • Total Badges: 32
    Badges: (View All)
    Level 6 Linux User Mobile User Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary
Re: 2159W
« Reply #16 on: October 21, 2013, 07:21:59 am »
there are always gains to be had but as far as big gains , the flywheel would be first, carb would be next and stuff like the squish , that saw is working well in your air so I would not do much to the porting cause most likely you will loose power, what works in 99% of the country does not work in your area on porting numbers

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #17 on: October 26, 2013, 07:25:57 pm »
Going to try an 8 tooth rim on it.

Offline Old Iron Logging

  • Nitro Hotsaw
  • *******
  • Posts: 1134
  • Karma: 82

  • Total Badges: 31
    Badges: (View All)
    Level 6 Nineth year Anniversary Eighth year Anniversary Seventh year Anniversary Sixth year Anniversary Fifth year Anniversary
Re: 2159W
« Reply #18 on: November 09, 2013, 01:18:49 pm »
Saw has the small spline drum, have to get the standard center drum before I can try an 8. If it gets any colder I am going to pull the pipe and use the saw for firewood.

 

Related Topics

  Subject / Started by Replies Last post
11 Replies
1437 Views
Last post October 24, 2012, 05:25:54 pm
by Old Iron Logging