Author Topic: 670 carburetor substitute?  (Read 510 times)

0 Members and 0 Guests are viewing this topic.

Offline farmboy

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 1035
  • Karma: 107
  • Location: Hayesville, NC
Re: 670 carburetor substitute?
« Reply #10 on: March 11, 2016, 09:28:38 pm »
Sorry you missed it.  The 62511 has same venturi size.  HS document for you.  http://www.tillotson.ie/docs/HSPartsList.pdf
Shep

Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2
Re: 670 carburetor substitute?
« Reply #11 on: March 12, 2016, 07:16:07 am »
Thanks for the link , I will definitely be doing some cross referencing over the next couple days

Sent from my SM-T330NU using Tapatalk


Offline snowsalot

  • 3 cube
  • *
  • Posts: 16
  • Karma: 2
Re: 670 carburetor substitute?
« Reply #12 on: March 23, 2016, 07:19:06 am »
OK I needed to use the saw so I cleaned everything up, put some threadlock on the H and L needles being careful not to get any inside the carb. Started it up set the needles and let it sit overnight for three threadlock to cure. Tried screws in the morning, can move them but they are much tighter. Did some final adjustments then added some epoxy on the screw heads and inside the little cover that goes over the screws, let that set up. Saw now runs better than it has in 10 years.
I do have a cheap China carb for husky 272 on the way to try with some modifications of course.


Sent from my SM-T330NU using Tapatalk


Online 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4001
  • Karma: 220
  • Location: Carpenter, Wyoming
Re: 670 carburetor substitute?
« Reply #13 on: March 24, 2016, 10:09:09 am »
Good deal.   
PP 505, 475, 445.

Online deezlfan

  • 4 cube
  • **
  • Posts: 57
  • Karma: 7
  • Location: Edge of Reality
Re: 670 carburetor substitute?
« Reply #14 on: March 25, 2016, 01:36:30 pm »
I've had success with just adding a tiny washer between the screw head and spring to raise the spring tension slightly. If you are putting washers on both screws and they interfere with each other, put one on the top of the spring and the other near the carb body. Hardest part is finding small enough washers.

Suppose if the spring is really bad a locking agent would work, but my worry is that most of those products get tougher/harder with time. You might find you can't adjust it as time goes on. 
Cause we just drag them down..... We just drag them down..... Until they're just like us !!!  Angry People by BNL

 

Related Topics

  Subject / Started by Replies Last post
14 Replies
372 Views
Last post December 28, 2013, 09:28:07 am
by SawTroll
2 Replies
79 Views
Last post February 26, 2014, 06:02:13 pm
by aclarke
7 Replies
267 Views
Last post May 24, 2014, 10:56:00 am
by KilliansRedLeo
6 Replies
107 Views
Last post July 18, 2014, 10:04:26 am
by srcarr52
8 Replies
245 Views
Last post July 22, 2014, 03:11:57 pm
by Cut4fun
6 Replies
202 Views
Last post November 28, 2016, 09:18:58 pm
by mdavlee .
3 Replies
267 Views
Last post March 09, 2017, 06:22:06 am
by Jacks54
2 Replies
120 Views
Last post May 12, 2017, 08:35:34 pm
by Oldachonoak
3 Replies
66 Views
Last post July 15, 2017, 10:07:47 pm
by shoesnsocks
12 Replies
73 Views
Last post Today at 09:47:32 pm
by dpjones