Author Topic: Jonsered 2054 bar studs  (Read 1172 times)

0 Members and 0 Guests are viewing this topic.

Offline dirtzilla

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Jonsered 2054 bar studs
« on: September 07, 2014, 10:34:31 pm »
Hi guys, I have to replace one of the studs holding the chain bar, I tried heating the stud with a small propane touch but the stud won't move, is this a reverse thread stud ???
thanks,

Share on Facebook Share on Twitter


Online srcarr52

  • 6 cube
  • ****
  • Posts: 288
  • Karma: 93
  • Location: IA
Re: Jonsered 2054 bar studs
« Reply #1 on: September 08, 2014, 10:24:00 am »
I'm not really familiar with that saw but most of the Jonsered and Husqvarna saws have pressed in bar studs from the inside of the oil tank.  Drain your oil tank, look in through the oil fill and you'll probably see the shoulder of the stud.  Just knock it into the tank with a hammer and fish it out.  The new stud can be pulled into the case with a the normal bar nut and a spacer (a larger nut). 

Offline 660magnum

  • Global Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 6437
  • Karma: 249
  • For The Love Of Chainsaws
  • Location: NCO
Re: Jonsered 2054 bar studs
« Reply #2 on: September 08, 2014, 10:57:23 am »
+1
We should share what we know... someone may learn...
That knowledge can live after us... and that "Pays It Forward".
Be all that you can be . . .

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2054 bar studs
« Reply #3 on: September 08, 2014, 12:05:23 pm »
Yep 2054 press in like he stated above.   Tap them back into the tank to remove.

 Use a magnet ext rod to go back in tank to install in hole.  Holds stud on end easily.    Then do as he says with nut to snog back up. Make sure head inside of tank is aligned with slots too. To keep from twisting etc.



Jonsered 2055, 2054, 2051

http://store.chainsawr.com/products/jonsered-2055-turbo-chainsaw-bar-stud-set

REDNECK Saw Repair Getter Done

Offline dirtzilla

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Re: Jonsered 2054 bar studs
« Reply #4 on: September 08, 2014, 12:47:48 pm »
not on this model, the muffler it right behind the  studs, after cleaning the dirt out now I can the stud bolt head, but I will have to remove the muffler to push stud out , I don't know if that's a good idea as this is a old saw, do this screws tend to seize  in thread because of all the heat or it should be ok.
thanks for the replies and pic guys.

Offline dirtzilla

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Re: Jonsered 2054 bar studs
« Reply #5 on: September 08, 2014, 12:51:57 pm »
this must be a earlier version -model of the 2054 , I can post a pic if someone wants to see, and help others too.

note to self,  don't lend ur saw to ANYONE , LOL

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2054 bar studs
« Reply #6 on: September 08, 2014, 01:21:29 pm »
Then that makes your job easier IMO.  I dont know a 2054.  Must be set up like 5000 bar studs behind the muffler.  Easy as heck.  still  just knock them back through and easier to install now.



REDNECK Saw Repair Getter Done

Offline dirtzilla

  • pruner
  • *
  • Posts: 4
  • Karma: 0
Re: Jonsered 2054 bar studs
« Reply #7 on: September 08, 2014, 01:36:16 pm »
I wonder is bolts securing muffler tend to be seized up, they are pretty small

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21876
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2054 bar studs
« Reply #8 on: September 08, 2014, 01:54:10 pm »
I have twisted of many not fun fix after that.  Use PB Blaster and let soak.    Might be able to use a little heat right there too.
REDNECK Saw Repair Getter Done

Offline Bobby Hricko

  • pruner
  • *
  • Posts: 1
  • Karma: 0
Re: Jonsered 2054 bar studs
« Reply #9 on: March 16, 2018, 03:22:03 pm »
My Jonsered 450 is the same way, have to take muffler out to get to bar studs. Now where do I get the bar studs from?

 

Related Topics

  Subject / Started by Replies Last post
Jonsered 490

Started by bloodontheice « 1 2 3 4 5 » Jonsered

44 Replies
6197 Views
Last post April 22, 2020, 12:26:59 pm
by Cut4fun .
2 Replies
864 Views
Last post March 21, 2011, 03:40:27 pm
by bafarm
Jonsered 111

Started by Cut4fun . « 1 2 3 » Jonsered

25 Replies
2380 Views
Last post August 30, 2014, 10:16:02 pm
by 660magnum
Jonsered 2054

Started by Cut4fun . « 1 2 » Jonsered

16 Replies
1163 Views
Last post April 21, 2013, 08:36:30 pm
by Old Iron Logging
Bar studs

Started by jmester Stihl

1 Replies
285 Views
Last post December 26, 2013, 10:03:18 pm
by jmester
Jonsered 525

Started by joker « 1 2 » Jonsered

10 Replies
1063 Views
Last post January 03, 2016, 02:42:43 pm
by leec
9 Replies
610 Views
Last post June 15, 2014, 06:07:36 pm
by green-zone
1 Replies
286 Views
Last post September 05, 2014, 05:54:49 pm
by malty
3 Replies
209 Views
Last post July 21, 2018, 09:30:48 am
by Toku70
0 Replies
163 Views
Last post July 21, 2018, 09:40:03 am
by Toku70