« previous next »
Pages: [1]   Go Down

Author Topic: Jonsered 535  (Read 526 times)

0 Members and 1 Guest are viewing this topic.

Offline Cut4fun_

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 7365
  • Karma: +65/-0
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Jonsered 535
« on: October 25, 2012, 11:28:25 am »
OK Mitch cough up the pic of a 45mm windowed jred 535 piston for me aka us.  ;)
Logged
REDNECK Saw Repair Getter Done

Offline Magnus

  • 6 cube
  • ****
  • Posts: 236
  • Karma: +22/-0
    • Chainsaw Collectors Forum
Re: Jonsered 535
« Reply #1 on: October 25, 2012, 12:10:16 pm »
I guess there is something special with this piston?
Logged
Chainsaw nut!

Offline Cut4fun_

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 7365
  • Karma: +65/-0
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 535
« Reply #2 on: October 25, 2012, 12:16:15 pm »
Quote from: Magnus on October 25, 2012, 12:10:16 pm
I guess there is something special with this piston?


Sure will be once I get info from Mitch.   ;)

 You got any info to share Magnus? Pics , measurements etc.

Jonsered 535 IPL  http://www.jonsered.com/ddoc/JONI/JONI1987_AAaa/JONI1987_AAaa_I8700002_.pdf
Logged
REDNECK Saw Repair Getter Done

Offline Magnus

  • 6 cube
  • ****
  • Posts: 236
  • Karma: +22/-0
    • Chainsaw Collectors Forum
Re: Jonsered 535
« Reply #3 on: October 25, 2012, 01:16:18 pm »
I can get pic's if you need. It should have 51cc, 32mm stroke, 45mm bore, HDA52 carb.
525 is almost the same, 44mm bore.
Logged
Chainsaw nut!

Offline Cut4fun_

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 7365
  • Karma: +65/-0
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 535
« Reply #4 on: October 25, 2012, 01:50:58 pm »
Please some pics.  Measurements of skirts how wide and top of pin to top of piston.   

Still looks hard to come by, but feebay shows some selling for less then $10  ;D
Logged
REDNECK Saw Repair Getter Done

Offline mweba

  • Piped Saw
  • *****
  • Posts: 338
  • Karma: +32/-0
Re: Jonsered 535
« Reply #5 on: October 25, 2012, 04:37:18 pm »
Haven't found a pic yet, believe it or not.  The pin height was the same but skirt was shorter.  I threw  this saw together fast for testing and never asked the guy to bring it back.  Asked him to cut his firewood with it and report back.
Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 338
  • Karma: +32/-0
Re: Jonsered 535
« Reply #6 on: October 25, 2012, 04:43:42 pm »
No help really but this is the saw running it...

Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 338
  • Karma: +32/-0
Re: Jonsered 535
« Reply #7 on: October 25, 2012, 05:18:39 pm »
OK, this is what I scribbled down. 

Piston pin to crown 13.7mm   Keeping in mind, the 535 is domed and that is not the top of dome measurement.
Over all height is 1.86mm shorter
pin is 10mm and needs to be widened to accept the rod and bearing....but not much


Will get this saw back and add to it.



 

Logged

Offline mweba

  • Piped Saw
  • *****
  • Posts: 338
  • Karma: +32/-0
Re: Jonsered 535
« Reply #8 on: October 25, 2012, 08:46:34 pm »
This is the Mac piston 350.  If one was to have a 3mm spacer, this piston would be perfect for the 535 or 55cp.  Have tried a couple different pistons and modded pistons in these saws.  Fun to smoke 346's with these  ;D

Logged
Pages: [1]   Go Up
« previous next »
 
Powered by EzPortal