« previous next »
Pages: [1]   Go Down

Author Topic: jonsered bar chain cutting equipment  (Read 761 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23517
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
jonsered bar chain cutting equipment
« on: July 01, 2015, 05:26:17 pm »
Logged

Share on Facebook Share on Twitter

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 71
  • Information collector
  • Location: Troms, North Norway
Re: jonsered bar chain cutting equipment
« Reply #1 on: July 29, 2015, 04:17:55 pm »
It is a bit odd that they recommend semi chisel only in .325, and chisel only in 3/8" - they (Husky/Jonsered) still do it that way.

Logged

Offline cello6996

  • 3 cube
  • *
  • Posts: 8
  • Karma: 0
Re: jonsered bar chain cutting equipment
« Reply #2 on: August 03, 2015, 08:30:34 pm »
Do you have one for a 910E?
Logged

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 71
  • Information collector
  • Location: Troms, North Norway
Re: jonsered bar chain cutting equipment
« Reply #3 on: August 04, 2015, 08:55:08 am »
Quote from: cello6996 on August 03, 2015, 08:30:34 pm
Do you have one for a 910E?
Oregon D024 if the studs haven't been changed. Those are getting hard to find, but it doesn't take much to widen the slot of D196/096 or D009 (large Husky) to fit.
Logged

Offline cello6996

  • 3 cube
  • *
  • Posts: 8
  • Karma: 0
Re: jonsered bar chain cutting equipment
« Reply #4 on: August 04, 2015, 11:18:33 pm »
I was finally able to get a 20 inch bar from Oregon as I guess they only do a production run vary rarely. I know I can go much larger than that and am thinking of get one just to have if the need arises to need on as all the parts for it are just whats left on someones shelf or taken from another saw. Just trying to look ahead
Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23517
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: jonsered bar chain cutting equipment
« Reply #5 on: August 05, 2015, 12:27:42 pm »
bar mount D024 http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/980fb87c02a98a5088256e0e001fee75?OpenDocument

Only one I see to buy is 20" too.  Like Niko says everyone seems to be converting the D176 or D009 to them.
Logged

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2117
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northwestern Wyoming
Re: jonsered bar chain cutting equipment
« Reply #6 on: August 05, 2015, 02:54:48 pm »
Quote from: Cut4fun . on August 05, 2015, 12:27:42 pm
bar mount D024 http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/980fb87c02a98a5088256e0e001fee75?OpenDocument

Only one I see to buy is 20" too.  Like Niko says everyone seems to be converting the D176 or D009 to them.

Yep.  You can open up the slot on a D176, D009, or D096/D196/UXL bar for a D024 mount.  The D176 just needs a bit more filing as it starts out at 8.22mm or so while the D009 starts out at 9mm and the D096/etc starts out at 9.5mm.

When Jonsered first transitioned from D024 to D009 mount bars on their saws, they provided an 'S' clip stud spacer to allow using the remaining stock of D024 bars on their 'new' D009 mount saws.
Logged

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 71
  • Information collector
  • Location: Troms, North Norway
Re: jonsered bar chain cutting equipment
« Reply #7 on: August 08, 2015, 11:48:41 am »
Quote from: Cut4fun . on August 05, 2015, 12:27:42 pm
bar mount D024 http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/980fb87c02a98a5088256e0e001fee75?OpenDocument

Only one I see to buy is 20" too.  Like Niko says everyone seems to be converting the D176 or D009 to them.

D096/196 likely are easier to convert to D024 - but the dl counts are "off", compared to usual Husky/Jonsered ones (bars are shorter for the same called length). The same likely is the case with D176 bars - so what I would use is D009, all in all....

Nominal bolt/slot sizes:

D024, 10 mm (usually 9.8 or so actual)

D196/096, 9.5 mm

D009, 9 mm (misprint on Acres site)

D176, 8 mm (actually more like 8.2, I believe)

D025/Stihl 3003, 12.1 mm (can be used with adaptors, but you have to make them yourself in this case)

Measure you bar bolts, before you do anything!
Logged

Offline SawTroll

  • Nitro Hotsaw
  • *******
  • Posts: 1196
  • Karma: 71
  • Information collector
  • Location: Troms, North Norway
Re: jonsered bar chain cutting equipment
« Reply #8 on: August 08, 2015, 12:07:52 pm »
Quote from: Eccentric on August 05, 2015, 02:54:48 pm
Quote from: Cut4fun . on August 05, 2015, 12:27:42 pm
bar mount D024 http://www.acresinternet.com/cscc.nsf/14711d8004b6ea7c88256e0c0001ff32/980fb87c02a98a5088256e0e001fee75?OpenDocument

Only one I see to buy is 20" too.  Like Niko says everyone seems to be converting the D176 or D009 to them.

When Jonsered first transitioned from D024 to D009 mount bars on their saws, they provided an 'S' clip stud spacer to allow using the remaining stock of D024 bars on their 'new' D009 mount saws.

That transition happened when the Husky factory took over production from the Partner factory about 1987.  ;)
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
12 Replies
946 Views 		Last post September 27, 2013, 12:32:35 pm
by Playinwood
4 Replies
389 Views 		Last post April 22, 2013, 12:22:51 am
by HolmenTree
8 Replies
354 Views 		Last post October 14, 2014, 09:54:07 pm
by farmboy
2 Replies
325 Views 		Last post February 05, 2014, 07:47:35 pm
by gunnusmc03
16 Replies
1107 Views 		Last post May 09, 2014, 12:25:01 am
by 3000 FPS
6 Replies
1067 Views 		Last post June 07, 2014, 05:35:02 pm
by Billyram
115 Replies
5435 Views 		Last post December 11, 2017, 09:49:26 pm
by Nathaniel Vansickle
14 Replies
620 Views 		Last post March 03, 2015, 11:47:18 am
by Ducksnuff870
5 Replies
427 Views 		Last post April 24, 2015, 07:12:32 pm
by jrdplowing
9 Replies
472 Views 		Last post August 11, 2021, 09:02:07 am
by John Mc