« previous next »
Pages: 1 2 [3] 4   Go Down

Author Topic: Jonsered 2159  (Read 5270 times)

0 Members and 5 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23989
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2159
« Reply #20 on: February 17, 2019, 02:39:46 pm »
 Thanks to Scott Kunz and his video I got this carb done right. Plus drilled the hole he talks about.  Shes running cutting again. Had wrong type check valve side in it too.

 can see the drill hole. Scott said do not run the blue check valve side in these. What someone had put in it. Tan in it now.

Logged

Offline trail twister

  • 5 cube
  • ***
  • Posts: 107
  • Karma: 18
Jonsered 2159
« Reply #21 on: August 13, 2020, 09:23:37 am »
Isn't pumping bar oil the way it should. Or should I say oil isn't getting to the bar as it should.

I need information on testing trhe pump once I get the clutch off and do not find a hole in the resivor to the pump line?

Al
Logged

Online ray benson

  • 6 cube
  • ****
  • Posts: 201
  • Karma: 100
  • Retired Industrial Electrician
  • Location: Indiana
Re: J red 2159.
« Reply #22 on: August 14, 2020, 08:52:52 am »

 Haven't worked on one. But here is a link to the service manual.
http://www.mediafire.com/file/z5unwzsu0741hu4/file
Logged
Like Like x 1 View List

Offline 3000 FPS

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 4708
  • Karma: 320
  • Location: Carpenter, Wyoming
Re: Jonsered 2159
« Reply #23 on: August 15, 2020, 12:27:52 pm »
You should be able to pull the bar and chain off and start the saw and see if there is oil coming out where the oiler hole is.   
Logged
PP 505, 475, 445.
Like Like x 1 View List

Offline Spike60

  • Piped Saw
  • *****
  • Posts: 369
  • Karma: 129
  • Location: Ulster County, NY
Re: Jonsered 2159
« Reply #24 on: August 17, 2020, 05:58:55 am »
Yup, running the saw without the bar and chain tells you right away if the saw is pumping oil or not. Those pumps rarely fail. The 2 common issues if it's the saw are the pump drive gear or the oil pick up screen coming off in the tank allowing sawdust to clog up the line. Both require pulling the clutch and all to fix.
Logged
Husqvarna-Jonsered

Ashokan Turf and Timber

845-657-6395
Like Like x 2 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23989
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2159
« Reply #25 on: December 21, 2021, 06:58:35 am »
I gave it 24hrs after showing folks on my CRG FB and good deal on a jonsered 2159.

Lunch time next day I said heck with it and bought the low hour saw myself. Will prob just flip it.

Only draw back was it is the CAT muffler model. Which that is a easy remedy.

Logged
Like Like x 1 View List

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4701
  • Karma: 216
  • OHIO REDNECK
Re: Jonsered 2159
« Reply #26 on: December 22, 2021, 08:08:35 am »
Everything checks out.  Appears they were running good red oil. Just not sure on gas but no water in it.

Could tell running wrong style of bar nuts on clutch cover.

Guessing these later came with the Zama carbs. Still even had the epa stops.

Tighten that pull rope up and get that blasted dealer sticker off that top cover.

Most wear I have ever seen on Tsu rails before.  Tip same way. They must never dressed them.



Logged

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4701
  • Karma: 216
  • OHIO REDNECK
Re: Jonsered 2159
« Reply #27 on: December 22, 2021, 08:39:52 am »
Manual specs

504 70 64 01
503 91 75 04
503 91 75-01

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23989
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2159
« Reply #28 on: December 23, 2021, 12:45:50 pm »
Just overlook my hack ways 😂.  Removing the tube and opening top and through a CAT husky muffler.

I can’t weld on mufflers so no cutting top deflector off to make it easy.

Now trying to decide if I should still gill both sides where I have them marked.

Logged

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 23989
  • Karma: 664
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Jonsered 2159
« Reply #29 on: December 23, 2021, 12:47:38 pm »
I said duck it. Both sides gill

Why oh why. Then they sold them with open mufflers too. 🤪

CAT drilled and tube removed. Now to test and tune later.

Triple exits now.

Pic don’t do justice for the like new witness lines still on piston



Logged
Pages: 1 2 [3] 4   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
Jonsered 490

Started by bloodontheice « 1 2 3 4 5 » Jonsered

45 Replies
10596 Views 		Last post March 08, 2022, 09:52:52 am
by Cut4fun .
Jonsered 590

Started by Cut4fun « 1 2 ... 5 6 » Jonsered

58 Replies
9158 Views 		Last post January 25, 2019, 03:05:09 pm
by Cut4fun .
Jonsered 535

Started by farmboy « 1 2 » Jonsered

19 Replies
5147 Views 		Last post April 30, 2018, 01:42:23 pm
by leec
26 Replies
4857 Views 		Last post August 03, 2013, 01:37:01 pm
by Cut4fun .
5 Replies
688 Views 		Last post August 08, 2013, 07:11:33 pm
by SawTroll
12 Replies
1525 Views 		Last post September 25, 2013, 09:27:52 pm
by Vance in AK
6 Replies
1036 Views 		Last post September 26, 2013, 03:16:07 pm
by sharkey
7 Replies
1016 Views 		Last post August 10, 2016, 06:31:22 pm
by wild262
3 Replies
793 Views 		Last post January 02, 2018, 06:01:56 am
by trail twister
3 Replies
280 Views 		Last post March 07, 2022, 01:50:03 pm
by Cut4fun .