Author Topic: Twin 2094 jonsered  (Read 248 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 17941
  • Karma: 338
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Twin 2094 jonsered
« on: August 21, 2016, 11:07:34 am »
Piped twin jonsered 2094 making 1 cut.  interesting

https://youtu.be/JWsTkwitnn4

REDNECK Saw Repair Getter Done

Social Buttons


Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2037
  • Karma: 199
  • Magnesium and Iron.
  • Location: Northern California.
Re: Twin 2094 jonsered
« Reply #1 on: August 23, 2016, 02:37:53 am »
Very cool.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Online deezlfan

  • 4 cube
  • **
  • Posts: 57
  • Karma: 7
  • Location: Edge of Reality
Re: Twin 2094 jonsered
« Reply #2 on: September 16, 2016, 11:28:50 am »
Sure wished the video showed him starting that saw! I can barely get my stock 2094 started without a comp release.....

Cause we just drag them down..... We just drag them down..... Until they're just like us !!!  Angry People by BNL

Online wild262

  • 5 cube
  • ***
  • Posts: 143
  • Karma: 23
Re: Twin 2094 jonsered
« Reply #3 on: September 16, 2016, 03:42:14 pm »
Sure wished the video showed him starting that saw! I can barely get my stock 2094 started without a comp release.....


I had one of these Beast for a while.  Put 1 of those oversized handsized handles on it,  and it sure made it a lot easier.   I think the later models had the comp. release.  Very strong saw in that cc range.

Offline HolmenTree

  • Nitro Hotsaw
  • *******
  • Posts: 844
  • Karma: 78
  • Location: Manitoba Canada
Re: Twin 2094 jonsered
« Reply #4 on: October 17, 2016, 10:35:27 pm »
Pretty cool alright! Looks like a well setup unit something from Australia, Neil could probably fill us in on that.
Making a living with a saw since age 16.

 

Related Topics

  Subject / Started by Replies Last post
Solo Twin

Started by mcbob « 1 2 3 4 » Solo

33 Replies
4179 Views
Last post March 16, 2016, 04:33:21 am
by dutchsawdoctor
42 Replies
4037 Views
Last post September 27, 2015, 10:44:22 am
by Cut4fun .
19 Replies
1462 Views
Last post April 06, 2015, 10:59:54 pm
by splitpost
13 Replies
695 Views
Last post March 12, 2013, 06:45:28 am
by Cut4fun
2 Replies
381 Views
Last post November 07, 2013, 12:47:11 pm
by 660magnum
2 Replies
238 Views
Last post September 23, 2014, 08:50:25 pm
by weimedog
4 Replies
218 Views
Last post April 23, 2015, 01:14:06 pm
by wild262
5 Replies
438 Views
Last post November 16, 2015, 08:30:21 am
by weimedog
Twin 090's

Started by mcbob Stihl

8 Replies
215 Views
Last post November 17, 2015, 01:10:17 am
by mcbob
2 Replies
189 Views
Last post April 11, 2016, 03:15:34 pm
by SDB777