Author Topic: 32" Husqvarna or Stihl mount Sprocket Nose Bar. Found one last weekend.  (Read 163 times)

0 Members and 0 Guests are viewing this topic.

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
I need a good usable 32" (105DL) 3/8 pitch sprocket nose bar for my Husky 288XP.  Large Husqvarna or 12.1mm Stihl mount (I have one of Homelite410's Husky/Stihl adapters to use if needed).  .050G or .063G is fine.  No .058G please. 

If your bar is a Windsor/Sandvik/Carlton/etc that takes the Windsor 'three rivet tips' and is .404-.063G, then I can use that............as I have 3/8 pitch tips for those bars. 

Alternatively, I could use a .404-.063G Oregon/Husqvarna/Cannon bar that takes the Oregon 'one rivet'  tips as I have one of those 3/8 tips that I could swap on.

Stuff I have to trade:

-Various old Homelite, McCulloch, Poulan parts and bars.

-Some Husqvarna parts. 

-A bunch (dozens) of new 'three rivet' Windsor 3/8 pitch sprocket tips. 

-A few new .404 pitch Oregon 'one rivet' tips. 

-A nice Husqvarna branded Oregon 20" small Husky mount 3/8-.050G RSN bar that takes the Oregon 'single rivet' tips.

-A new German made Carlton small Husky mount .325-.058G RSN bar that takes the Oregon 'single rivet' tips.

Also have some folded presidential pictures (and electronic versions) to trade.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Share on Facebook Share on Twitter


Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: 32" Husqvarna or Stihl mount Sprocket Nose Bar.
« Reply #1 on: November 05, 2013, 12:38:23 am »
Picked up a bar from a friend at our GTG last weekend. 8)
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

 

Related Topics

  Subject / Started by Replies Last post
18 Replies
1896 Views
Last post October 04, 2013, 10:49:37 pm
by Philbert
24 Replies
1421 Views
Last post October 25, 2012, 08:45:50 am
by Al Smith
1 Replies
180 Views
Last post November 07, 2012, 10:27:43 pm
by Roanoker494
1 Replies
160 Views
Last post October 10, 2013, 10:18:54 pm
by 660magnum
2 Replies
273 Views
Last post March 16, 2014, 12:18:29 pm
by KilliansRedLeo
2 Replies
167 Views
Last post April 16, 2014, 06:44:18 pm
by winland
4 Replies
137 Views
Last post April 03, 2015, 09:25:53 am
by wild262
8 Replies
191 Views
Last post June 17, 2015, 01:20:14 pm
by RoyM
0 Replies
125 Views
Last post October 29, 2017, 09:09:27 pm
by weimedog
6 Replies
141 Views
Last post May 05, 2020, 02:02:00 pm
by Eddie Southgate