Author Topic: Husqvarna 338XPT  (Read 414 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Husqvarna 338XPT
« on: November 22, 2013, 05:44:18 pm »
Husky 338 year 2011 NE.

$240 with like new 12" in pic or $220 with used 14" forester and stihl rm3 chain not in pic. Plus UPS shipping. 





REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 338XPT
« Reply #1 on: December 10, 2013, 02:10:40 pm »
The T540 is out and willing to work with someone to move this 338XPT with used 14" forester and stihl rm3 chain not in pic.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 338XPT
« Reply #2 on: December 13, 2013, 10:18:04 pm »
Kevin contact this guy on AS...

http://www.arboristsite.com/community/threads/wtb-husqvarna-334-335-or-338.248229/

Edit:

The damn link keeps changing when I post.  Just go to the Trading Post on AS.  There's a guy looking for a 334/335/338 Husky.
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 338XPT
« Reply #3 on: December 13, 2013, 10:21:33 pm »
Done. Thanks for heads up.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Husqvarna 338XPT
« Reply #4 on: December 13, 2013, 10:38:28 pm »
Anytime my friend. ;D
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 338XPT
« Reply #5 on: December 13, 2013, 10:40:25 pm »
I know what it means when I see the chainsawsite.   ;)  No biggie here  :D 8)
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 338XPT
« Reply #6 on: December 16, 2013, 03:49:26 pm »
To the guy waiting on this. I tested 338 today and it was acting like it is going to need a carb kit.  Been setting since Aug or early Sept. It is a 2011 and never had a carb kit put in. So right now I wont sale it the way it is with idle and taking throttle.

Going to lock thread till I get it fixed and then will update.
REDNECK Saw Repair Getter Done

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4109
  • Karma: 166
  • OHIO REDNECK
Re: Husqvarna 338XPT
« Reply #7 on: December 27, 2013, 07:34:52 pm »
Finally made time and warm enough in barn to work some.  2011 husky 338 is back on market now. 

Just installed new carb kit. Installed a new purge bulb while I had it down. Cleaned and reset coil gap.  Put the 14" used forester bar and oregon chain on it this time. Being 2 folks were wanting the 14".  Sharpened the chain.

Started, cut, tuned  today. Ready to go.

New pics.
REDNECK Saw Repair

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22076
  • Karma: 548
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Husqvarna 338XPT
« Reply #8 on: January 04, 2014, 04:42:43 pm »
Just left with new owner. SOLD
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
15 Replies
1624 Views
Last post December 15, 2013, 11:46:24 am
by KilliansRedLeo
25 Replies
1013 Views
Last post January 01, 2012, 12:13:11 pm
by EHP
2 Replies
254 Views
Last post April 27, 2013, 04:08:24 pm
by Old Iron Logging
37 Replies
959 Views
Last post March 08, 2014, 03:15:48 pm
by SawTroll
8 Replies
622 Views
Last post January 02, 2014, 07:56:43 pm
by Eccentric
4 Replies
253 Views
Last post November 23, 2014, 03:36:23 pm
by Cut4fun .
2 Replies
281 Views
Last post May 15, 2016, 04:59:09 am
by Eccentric
7 Replies
283 Views
Last post May 15, 2016, 04:49:22 am
by Eccentric
10 Replies
462 Views
Last post June 21, 2016, 03:18:11 pm
by Giles
2 Replies
279 Views
Last post December 26, 2016, 05:32:01 pm
by SawTroll