« previous next »
Pages: [1]   Go Down

Author Topic: Mac 10-10 manual oiler....  (Read 756 times)

0 Members and 0 Guests are viewing this topic.

Offline mrcaptainbob

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Mac 10-10 manual oiler....
« on: April 18, 2011, 12:34:07 am »
How do I get the manual oiler rod/shaft out? It appears the knob handle is broken and that the rod is also not connected. Do I need to disassemble the whole saw to get at this? Is there a better way? Other than that the saw runs fine.
Logged

Share on Facebook Share on Twitter

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: Mac 10-10 manual oiler....
« Reply #1 on: April 18, 2011, 07:02:11 am »
There should be a little roll pin holding the button in .I think they are all the same but I'll look in a little bit to see .
Logged

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: Mac 10-10 manual oiler....
« Reply #2 on: April 18, 2011, 09:25:11 am »
I looked at several 10 series out in the shed .It's as I said a tiny little roll pin .

The easiest way is to either use a very thin punch or cut the point off a finish nail and tap the pin out the bottom .Then it's just a matter of pulling the button rod and all out .
Logged

Offline mrcaptainbob

  • pruner
  • *
  • Posts: 2
  • Karma: 0
Re: Mac 10-10 manual oiler....
« Reply #3 on: April 19, 2011, 12:18:12 am »
Thanks, Al. I'll check into that Wednesday....
Logged

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2753
  • Karma: 170
Re: Mac 10-10 manual oiler....
« Reply #4 on: April 19, 2011, 05:08:32 am »
Say,yesterday I ordered a part from Scott and in looking over his site he has a complete button and shaft for a 10-10 for cheap .http://store.chainsawr.com/
Logged
Pages: [1]   Go Up
« previous next »
 

Related Topics

  Subject / Started by Replies Last post
ms170 oiler

Started by bigd74 Stihl

7 Replies
1069 Views 		Last post January 12, 2012, 08:18:14 pm
by bigd74
0 Replies
1025 Views 		Last post April 04, 2012, 12:29:54 pm
by Cut4fun
2 Replies
307 Views 		Last post July 21, 2012, 04:06:23 am
by pete
8 Replies
617 Views 		Last post August 30, 2012, 12:53:08 pm
by Remington
9 Replies
447 Views 		Last post January 27, 2013, 09:53:49 pm
by BikerBill
1 Replies
475 Views 		Last post November 20, 2012, 06:32:27 pm
by 660magnum
3 Replies
245 Views 		Last post September 05, 2013, 09:23:16 am
by jcsmith
PP 655 Oiler

Started by blsnelling « 1 2 » Poulan

10 Replies
347 Views 		Last post October 18, 2013, 11:20:35 pm
by blsnelling
166 oiler

Started by chadstone « 1 2 3 » Dolmar Makita

21 Replies
742 Views 		Last post August 05, 2014, 07:38:22 pm
by Cut4fun
5 Replies
520 Views 		Last post January 19, 2017, 09:55:19 pm
by farmboy