Author Topic: Mac 10-10 manual oiler....  (Read 1043 times)

0 Members and 46 Guests are viewing this topic.

Offline mrcaptainbob

  • pruner
  • *
  • Posts: 2
  • Karma: 0

  • Total Badges: 7
    Badges: (View All)
    Third year Anniversary Level 2 Second year Anniversary Topic Starter Level 1 First Post
Mac 10-10 manual oiler....
« on: April 18, 2011, 12:34:07 am »
How do I get the manual oiler rod/shaft out? It appears the knob handle is broken and that the rod is also not connected. Do I need to disassemble the whole saw to get at this? Is there a better way? Other than that the saw runs fine.

Share on Facebook Share on Twitter


Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: Mac 10-10 manual oiler....
« Reply #1 on: April 18, 2011, 07:02:11 am »
There should be a little roll pin holding the button in .I think they are all the same but I'll look in a little bit to see .

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: Mac 10-10 manual oiler....
« Reply #2 on: April 18, 2011, 09:25:11 am »
I looked at several 10 series out in the shed .It's as I said a tiny little roll pin .

The easiest way is to either use a very thin punch or cut the point off a finish nail and tap the pin out the bottom .Then it's just a matter of pulling the button rod and all out .

Offline mrcaptainbob

  • pruner
  • *
  • Posts: 2
  • Karma: 0

  • Total Badges: 7
    Badges: (View All)
    Third year Anniversary Level 2 Second year Anniversary Topic Starter Level 1 First Post
Re: Mac 10-10 manual oiler....
« Reply #3 on: April 19, 2011, 12:18:12 am »
Thanks, Al. I'll check into that Wednesday....

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2779
  • Karma: 181

  • Total Badges: 34
    Badges: (View All)
    Tenth year Anniversary Nineth year Anniversary Eighth year Anniversary Level 6 Seventh year Anniversary Sixth year Anniversary
Re: Mac 10-10 manual oiler....
« Reply #4 on: April 19, 2011, 05:08:32 am »
Say,yesterday I ordered a part from Scott and in looking over his site he has a complete button and shaft for a 10-10 for cheap .http://store.chainsawr.com/

 

Related Topics

  Subject / Started by Replies Last post
ms170 oiler

Started by bigd74 Stihl

7 Replies
1438 Views
Last post January 12, 2012, 08:18:14 pm
by bigd74
0 Replies
1615 Views
Last post April 04, 2012, 12:29:54 pm
by Cut4fun
1 Replies
562 Views
Last post April 28, 2012, 08:33:30 am
by Cut4fun .
2 Replies
560 Views
Last post July 21, 2012, 04:06:23 am
by pete
8 Replies
937 Views
Last post August 30, 2012, 12:53:08 pm
by Remington
3 Replies
558 Views
Last post September 05, 2013, 09:23:16 am
by jcsmith
PP 655 Oiler

Started by blsnelling « 1 2 » Poulan

10 Replies
851 Views
Last post October 18, 2013, 11:20:35 pm
by blsnelling
166 oiler

Started by chadstone « 1 2 3 » Dolmar Makita

21 Replies
1892 Views
Last post August 05, 2014, 07:38:22 pm
by Cut4fun
5 Replies
1356 Views
Last post January 19, 2017, 09:55:19 pm
by farmboy
7 Replies
238 Views
Last post August 13, 2023, 12:27:07 pm
by 3000 FPS