Author Topic: Mac Cat 35cc 38cc 32cc  (Read 1671 times)

0 Members and 0 Guests are viewing this topic.

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 209
  • Karma: 30
Re: Mac Cat 35cc 38cc 32cc
« Reply #20 on: July 28, 2015, 12:26:10 pm »
I'm pretty sure mine is actually 32cc and the A/V doner saw was really 38cc - however they are both early saws, and I recall seeing somewhere that replacement parts were only available in 38cc.  So maybe they figured out what Poulan did that it wasn't cost effective to make several displacements so close. 

The oil pump is under the flywheel, but I did not take it apart as mine worked fine.  The pump is driven by a worm gear concentric with the crank, but the gear spins freely on the crank - there is a coil spring between the flywheel and the worm which drives it but acts like a clutch.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20223
  • Karma: 440
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Mac Cat 35cc 38cc 32cc
« Reply #21 on: July 28, 2015, 05:12:15 pm »
Great pics. Thanks
REDNECK Saw Repair Getter Done

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20223
  • Karma: 440
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Mac Cat 35cc 38cc 32cc
« Reply #22 on: July 31, 2015, 02:42:51 pm »
I'm done fiddle farting with these things. They are just not worth putting any money into for me to resell. I have $15 and $20 in them already.

The AV version says 35cc but 38cc on sticker,  needs carb or a complete carb kit rebuild for the walbro IMO. Plus the oiler dont work and I'm not digging in to see.

The 2.0 non-av one ran but pulled the zama to test on the AV one. The throttle shaft broke when removing. Also stole the plastic choke lever for AV.

Both carbs are in plastic bags. Shelving them for parts unless someone else is interested in them.  Trades or just want to break even.




REDNECK Saw Repair Getter Done

Offline Chris-PA

  • 6 cube
  • ****
  • Posts: 209
  • Karma: 30
Re: Mac Cat 35cc 38cc 32cc
« Reply #23 on: July 31, 2015, 04:47:54 pm »
That's a shame - you might run into the right parts eventually.  Mine is a joy to use now with A/V and the minor mods I did and a 12" bar.  It's perfect for small jobs and will easily pull that bar in anything.  I like the feel and it will sometimes start in 1 pull cold. 

Offline dannyupsolate

  • Piped Saw
  • *****
  • Posts: 327
  • Karma: 28
Re: Mac Cat 35cc 38cc 32cc
« Reply #24 on: July 31, 2015, 08:53:58 pm »
all I have in my little beaver 2.0 is a few inches of tygon anybody that wants it for less than $50.00 bucks can go use a handsaw.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 20223
  • Karma: 440
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Mac Cat 35cc 38cc 32cc
« Reply #25 on: August 25, 2015, 11:27:14 am »
Mac cat 38cc IPL is in this thread.

Bump
REDNECK Saw Repair Getter Done

 

Related Topics

  Subject / Started by Replies Last post
31 Replies
2170 Views
Last post August 22, 2017, 01:51:25 pm
by Cut4fun .
1 Replies
370 Views
Last post December 14, 2012, 03:48:10 pm
by oldpart
6 Replies
197 Views
Last post November 12, 2013, 05:21:48 pm
by 660magnum
2 Replies
93 Views
Last post September 12, 2015, 03:49:25 pm
by Cut4fun .
5 Replies
312 Views
Last post June 08, 2016, 10:22:51 pm
by leec
77 Replies
699 Views
Last post February 16, 2017, 08:59:51 pm
by stubnail67