Author Topic: McCULLOCH DOUBLE EAGLE 50 Titan 50  (Read 5081 times)

0 Members and 0 Guests are viewing this topic.

Offline pete

  • Piped Saw
  • *****
  • Posts: 496
  • Karma: 37
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #10 on: May 08, 2012, 06:59:59 am »
hi guys,came here searching for fuel line size  I have 3 of these plus a titan 57 that a lot of parts swap over from but yes coils are a problem,It is hard to see where the fuel lines run  and the one I need to put lines into now have crumbled away leaving some springs and crumbled black hose.I would gratefully take any suggestions on this job,as I dont want to fiddle with the other 2 while they still run they are pigs to start and do need carb kits .
But I will fiddle with this one firstI came here for a look and registered when this site first opened there wasn't much here then and tonight is my first visit back in a long time thanks to a google search link that I came across while looking for the right fuel linbe size.
I was blown away there is enough reading here to keep me happy all winter congratulations it's great :) :) :)

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #11 on: May 09, 2012, 10:53:49 am »
Pete

I have pics on another laptop.  Will post them later today.  I've been talked into doing this job again (50 and 57) so I will better document it.


Also, looking for usable 50 pistons if anyone has a source or parts saw....

Offline pete

  • Piped Saw
  • *****
  • Posts: 496
  • Karma: 37
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #12 on: May 10, 2012, 07:11:09 am »
thanks pics of the job would be great,these are good firewood cutters with a 16 inch bar on them ,but number 3 was bought with no spark tried another coil no better put the original back on and fuel down the carb she fires, but as I mentioned the fuel lines are shot. so your pics will be a  big help

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Winner Winner x 1 View List

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 22121
  • Karma: 551
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #14 on: May 10, 2012, 08:49:35 pm »
Wow Mitch you wasnt kidding about the fuel line pita part early in thread.  Good job on the video info.
REDNECK Saw Repair Getter Done

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2757
  • Karma: 172
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #15 on: May 10, 2012, 11:02:58 pm »
Nice vid .Along the same lines I had to fish a new line on the Titan 70 and it was somewhat a pain in the buttocks as well .Worse today was a fuel line for a 2100 Huskey but that belongs in  a different sub topic of the forum ,

Offline pete

  • Piped Saw
  • *****
  • Posts: 496
  • Karma: 37
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #16 on: May 11, 2012, 08:05:16 am »
Thank you very much for taking the time to make the video as stated way better than pics,just getting the correct fuel line was worth it.The pressure fitting you describe is it along the lines of a piece of fuel line with a setscrew in it,,I am not looking forward to this as once I have done one and it works I gotta do 2 more.As the hard starting I am now attributing to fuel lines,so may as well rering the other 2 while I am at it they dont have as much compression as the first to be fixed cheers and thanks

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #17 on: May 12, 2012, 06:42:51 pm »
Anytime I can help.

Oil tank line


Titan oil line by mweba1, on Flickr

Oil feed line on the right.  When putting the tank on make sure this line goes over all others and right up against the intake boot....this is the easiest one to pinch.  Line on the left is the impulse


Titan lines by mweba1, on Flickr

Fuel line in tank end.


Titan lines by mweba1, on Flickr

Fuel line to carb


Titan by mweba1, on Flickr

Tank lines already installed ready to assemble.  Top left is oil tank breather.


Titan lines by mweba1, on Flickr

Winner Winner x 1 View List

Offline mweba

  • Piped Saw
  • *****
  • Posts: 392
  • Karma: 55
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #18 on: May 12, 2012, 06:46:11 pm »
This is the exact configuration for the 50 although this is a 57.  I eliminated the thumb oiler on this saw due to the plunger not functioning anyway.  Would recommend doing this on all 57's......makes the job WAY easier and it oils plenty without.

Offline pete

  • Piped Saw
  • *****
  • Posts: 496
  • Karma: 37
Re: McCULLOCH DOUBLE EAGLE 50
« Reply #19 on: July 07, 2013, 04:54:09 am »
http://www.ebay.com.au/itm/2-McCulloch-TITAN-50-Chainsaw-Parts-Repair-Worked-Great-Just-Need-Fuel-Lines-/281128972547?pt=US_Chainsaws&hash=item417497b103&_uhb=1
just put this up as I remember someone looking for pistons, (mewba) If I was  a lot closer I would buy them just for the coils 

 

Related Topics

  Subject / Started by Replies Last post
30 Replies
3283 Views
Last post January 01, 2018, 11:24:35 am
by Cut4fun .
32 Replies
3847 Views
Last post July 11, 2016, 03:47:47 pm
by Al Smith
1 Replies
400 Views
Last post March 01, 2012, 05:06:05 pm
by Old Iron Logging
3 Replies
911 Views
Last post December 13, 2013, 05:00:34 pm
by brokenbudget
8 Replies
419 Views
Last post March 21, 2015, 02:08:38 pm
by 660magnum
5 Replies
400 Views
Last post November 30, 2014, 10:31:22 pm
by mikehonda
0 Replies
461 Views
Last post December 01, 2014, 12:30:40 am
by mikehonda
2 Replies
249 Views
Last post January 23, 2016, 11:12:56 pm
by concretegrazer
3 Replies
272 Views
Last post January 27, 2016, 09:42:22 pm
by mikehonda
0 Replies
237 Views
Last post January 27, 2016, 09:38:58 pm
by mikehonda