Author Topic: primer bulb on mcc 1435  (Read 215 times)

0 Members and 0 Guests are viewing this topic.

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1
primer bulb on mcc 1435
« on: September 13, 2015, 09:28:20 am »
how critical is primer bulb on this saw,it is missing the pump bulb but the housing, lines, and duckbill is there,but is it possible if i run the tank out of gas and then refill and try to restart,that without the primer bulb it is not getting any gas up in the line to the carb,and does it matter the way it is hooked up because i noticed a longer fitting and a short fitting on the back of the primer assembly,does the long come from the tank and the short go to carb,thanks for any help

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21878
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
REDNECK Saw Repair Getter Done

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1
Re: primer bulb on mcc 1435
« Reply #2 on: September 13, 2015, 10:03:07 am »
acctualy my 1435 is compleatly different,but thanks for the info

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: primer bulb on mcc 1435
« Reply #3 on: September 13, 2015, 10:10:18 am »
REDNECK Saw Repair

Offline Cut4fun

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 4045
  • Karma: 159
  • OHIO REDNECK
Re: primer bulb on mcc 1435
« Reply #4 on: September 13, 2015, 10:13:12 am »
Look at these and match yours up.  McCulloch Chainsaw Parts List Directory  IPL list    http://www.barrettsmallengine.com/mcculloch/chainsawpartslist.html
REDNECK Saw Repair

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1
Re: primer bulb on mcc 1435
« Reply #5 on: September 13, 2015, 12:31:16 pm »
yes that is the way my bulb is situated but it does not show the line routing,does it matter,i think yes because of the 2 different size nipples on the bulb, i have a new bulb coming maybe it will show routing,thanks

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21878
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: primer bulb on mcc 1435
« Reply #6 on: September 13, 2015, 12:35:09 pm »
Yes it matters.  Look close on back of primer base. Should show in and out or at least one of them.
REDNECK Saw Repair Getter Done

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1
Re: primer bulb on mcc 1435
« Reply #7 on: September 13, 2015, 02:07:20 pm »
ok thanks

Offline jrdplowing

  • 4 cube
  • **
  • Posts: 26
  • Karma: 1
Re: primer bulb on mcc 1435
« Reply #8 on: September 13, 2015, 02:47:57 pm »
yes you were right the small nipple is marked in,so i pulled it over alot and no fuel will come up the line,so iam going to wait and try with the primer bulb,and dont try wetting the air filter it just floods it and wont start,thanks again

 

Related Topics

  Subject / Started by Replies Last post
9 Replies
1164 Views
Last post November 05, 2014, 10:35:55 pm
by 67L36Driver
3 Replies
285 Views
Last post October 06, 2013, 09:51:24 pm
by Eccentric
2 Replies
651 Views
Last post November 06, 2013, 07:57:16 pm
by 3000 FPS
2 Replies
191 Views
Last post September 12, 2015, 09:44:05 pm
by jrdplowing
8 Replies
242 Views
Last post September 19, 2015, 08:18:24 am
by jrdplowing
4 Replies
249 Views
Last post October 19, 2015, 07:20:58 pm
by jrdplowing
2 Replies
335 Views
Last post February 02, 2016, 07:30:39 pm
by Cycledude
2 Replies
370 Views
Last post May 10, 2017, 09:31:04 am
by Nathaniel Vansickle