Author Topic: Titan 70 piston specs  (Read 462 times)

0 Members and 0 Guests are viewing this topic.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Titan 70 piston specs
« on: August 04, 2015, 08:02:21 pm »
Anyone know the specs on the mac  titan 70 piston?  Pins size,  etc.
REDNECK Saw Repair Getter Done

Share on Facebook Share on Twitter


Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Titan 70 piston specs
« Reply #1 on: August 05, 2015, 01:52:42 pm »
@jacob j. you might be the only one I know with a piston in hand that would know specs on these. Any info.
REDNECK Saw Repair Getter Done

Offline Eccentric

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2110
  • Karma: 217
  • Magnesium and Iron.
  • Location: Northern California.
Re: Titan 70 piston specs
« Reply #2 on: August 05, 2015, 02:51:59 pm »
JJ is probably very busy with the various wildfires going on right now.  May or may not be a bit of time before he can answer your question...
-Aaron

For older saws:
Tune the H side so that it 4-strokes (burbles) at WOT unloaded and just cleans up when under load.
When you lift cutting load, the saw should immediately revert to 4-stroking.  Fine tune the transition point for the wood you're cutting.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Titan 70 piston specs
« Reply #3 on: August 05, 2015, 03:15:30 pm »
JJ is probably very busy with the various wildfires going on right now.  May or may not be a bit of time before he can answer your question...

Been seeing that on the news  :o .  I have all the time in the world.
REDNECK Saw Repair Getter Done

Offline Al Smith

  • Moderator
  • Nitro Hotsaw
  • *******
  • Posts: 2746
  • Karma: 164
Re: Titan 70 piston specs
« Reply #4 on: August 07, 2015, 10:05:36 pm »
If I'm not mistaken there might be a couple on flea bay if you're looking for one.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Titan 70 piston specs
« Reply #5 on: August 11, 2015, 02:34:08 pm »
So far I havent found just the piston to buy. But have found p+c together and just cyl. 

Just wanting specs from piston.
REDNECK Saw Repair Getter Done

Offline nenicu

  • 4 cube
  • **
  • Posts: 65
  • Karma: 7
Re: Titan 70 piston specs
« Reply #6 on: January 19, 2016, 07:42:24 am »
McCuloch Titan 70 piston:compression 23, top of pin to top side 17, total 40. I think a Husqvarna 268 xp piston shoul work instead of the original.

Offline nenicu

  • 4 cube
  • **
  • Posts: 65
  • Karma: 7
Re: Titan 70 piston specs
« Reply #7 on: January 19, 2016, 07:48:25 am »
Piston is 35 mm wide, 16,3  between piston  bosses, 12 mm pin.

Offline Cut4fun .

  • Administrator
  • Nitro Hotsaw
  • *******
  • Posts: 21877
  • Karma: 522
  • OHIO REDNECK Saw Repair Getter Done
    • Redneck Chainsaw Repair
Re: Titan 70 piston specs
« Reply #8 on: January 19, 2016, 01:40:55 pm »
McCuloch Titan 70 piston:compression 23, top of pin to top side 17, total 40. I think a Husqvarna 268 xp piston shoul work instead of the original.

Piston is 35 mm wide, 16,3  between piston  bosses, 12 mm pin.

Thanks for info.

NOS titan 70 pistons are so cheap here. I was just looking for a use for them. ;)
REDNECK Saw Repair Getter Done

Offline nenicu

  • 4 cube
  • **
  • Posts: 65
  • Karma: 7
Re: Titan 70 piston specs
« Reply #9 on: January 19, 2016, 02:48:07 pm »
 I just got a Titan 70. I don't have a source for a piston and i was thinking to use a H 268 piston.

 

Related Topics

  Subject / Started by Replies Last post
30 Replies
3222 Views
Last post January 01, 2018, 11:24:35 am
by Cut4fun .
3 Replies
522 Views
Last post January 23, 2016, 10:29:14 pm
by mikehonda
32 Replies
3762 Views
Last post July 11, 2016, 03:47:47 pm
by Al Smith
4 Replies
822 Views
Last post November 04, 2012, 08:29:53 pm
by CTownsend
2 Replies
363 Views
Last post June 19, 2014, 03:32:20 pm
by farmboy
5 Replies
380 Views
Last post November 30, 2014, 10:31:22 pm
by mikehonda
0 Replies
447 Views
Last post December 01, 2014, 12:30:40 am
by mikehonda
3 Replies
262 Views
Last post January 27, 2016, 09:42:22 pm
by mikehonda
1 Replies
115 Views
Last post June 17, 2016, 04:52:19 pm
by 1manband
1 Replies
188 Views
Last post December 07, 2017, 09:51:30 am
by mdavlee .